Assessments - 4, GPA: 4 ( )

Fabricante : Yamaha Arquivo Tamanho: 4.18 mb Arquivo Nome : Língua de Ensino:

5-2 Attach the cord holders to the rear panel as shown, then clip the cord into the holders. 5-3 Use a vinyl tie to take up any slack in the pedal cord. PEDAL 240 127 110220 6-1 5-2 5-3 6-2 5-1 6. Connect the power cord. 6-1 Set the voltage selector (for models that feature a voltage selector). Voltage Selector Before connecting the AC power cord, check the setting of the voltage selector which is provided in some areas. To set the selector for 110V, 127V, 220V or 240V main voltages, use a “minus” screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the panel. The voltage selector is set at 240V when the unit is initially shipped. After the proper voltage has been selected, connect the AC power cord to the AC IN and an AC wall outlet. A plug adaptor may be also provided in some areas to match the pin configuration of the AC wall outlets in your area. 6-2 Pass the power cord from the rear and insert the plug into the power connector. 7. Set the adjuster. Rotate the adjuster until the pedal box comes in firm contact with the floor surface. 8. Attach the headphone hanger. Use the included two screws (4 x 10 mm) to attach the hanger as shown in the illustration. After completing the assembly, please check the following. • Are there any parts left over? Review the assembly procedure and correct any errors. • Is the instrument clear of doors and other movable fixtures? Move the instrument to an appropriate location. • Does the instrument make a rattling noise when you shake it? Tighten all screws. • Does the pedal box rattle or give way when you step on the pedals? Turn the adjuster so that it is set firmly against the floor. • Are the pedal and power cords inserted securely into the sockets? Check the connection. • If the unit creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly diagrams and retighten all screws. CAUTION When moving the instrument after assembly, always hold instrument by the lower surface in the front of the main unit and by the handles in the rear of the main unit. CAUTION Do not hold the key cover or top portion. Improper handling can result in damage to the instrument or personal injury. Top portion Key cover Hold here. Do not hold here. ENGLISH CLP-370/340/330, CLP-S308/S306 Owner’s Manual 83 CLP-340/330: Keyboard Stand Assembly CLP-340/330: Keyboard Stand Assembly ENGLISH CAUTION • Assemble the unit on a flat floor surface. • Be careful not to confuse parts, and be sure to install all parts in the correct orientation. Please assemble the unit in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use only the included screws of the specified sizes. Do not use any other screws. Use of incorrect screws can cause damage or malfunction of the product. • Be sure to tighten all screws upon completing assembly of the unit. •To disassemble the unit, reverse the assembly sequence given below. Remove all parts from the package and make sure you have all of the items. Have a Philips-head (+) screwdriver of the appropriate size ready. A B C ED Foamed styrol pads Remove foamed styrol pads from the package, position them on the floor, then place A on top of them. Position the pads so that they will not hide the connectors on the bottom of A. A bundled pedal cord is attached to the reverse side. 6 x 25 mm long screws x 4 6 x 16 mm short screws x 4 4 x 12 mm thin screws x 2 4 x 10 mm thin screws x 2 4 x 20 mm tapping screws x 4 Headphone hanger Headphone hanger Cord holders x 2 Power cord Assembly Parts 84 CLP-370/340/330, CLP-S308/S306 Owner’s Manual CLP-340/330: Keyboard Stand Assembly 1. Attach C to D and E. D C E1-1 1-2 1-1 Untie and straighten out the bundled pedal cord. Do not discard the vinyl tie. You will need it later in step 5. 1-2 Attach D and E to C by tightening four long screws (6 x 25 mm). 2. Attach B. Depending on the model of Clavinova you purchased, the surface color of one side of B may be different from the other side. In this case, position B so that the side of the surface color most similar to D and E faces you (as you would play the instrument). 2-1 Place the lower side of B on each foot of D and E, then align the screw holes on the upper side of B with the bracket holes on D and E. 2-2 Attach the top corners of B to D and E by finger- tightening two thin screws (4 x 12 mm). 2-3 While pushing the lower part of D and E from outside, secure the bottom end of B using four tapping screws (4 x 20 mm). 2-4 Securely tighten the screws on the top of B that were attached in Step 2-2. 2-2 2-4 3. Mount A. Be sure to place your hands at least 15 cm from either end of the main unit when positioning it. A 15 cm or further in 15 cm or further in CAUTION Be extra careful not to drop or let your fingers be pinched by the main unit. CAUTION Do not hold the main unit in any position other than the position specified above. 4. Secure A. 4-1 Adjust ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :