Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
IMPORTANT Stored two-stroke fuel may separate. ALWAYS shake fuel container thoroughly before each use. B A D C 12 IMPORTANT Recoil starter: Use short pulls - only 1/2 ~ 2/3 of rope for starting. Do not allow the rope to snap back in. Always hold the unit firmly. 5. Recoil Starter Place the unit on a flat, clear area. Firmly grasp throttle grip with left hand and rapidly pull recoil starter handle/rope (E) until engine fires , or maximum 5 pulls. 6. Choke move choke lever (C) to Run ( ) position if necessary, restart engine. NOTE If engine does not start after 5 pulls, repeat instructions 3-6. 7. After engine warm up, gradually depress throttle trigger to increase engine RPM to operating speed. NOTE Allow engine to warm up before use. STARTING WARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke. 1. Stop Switch Move stop switch button (A) away from the STOP position. 2. Throttle Position Lever Move throttle position lever (B) midway between idle and full throttle positions. 3. Purge Bulb Pump purge bulb (D) until fuel is visible and flows freely in the clear fuel tank return line. 4. Recoil Starter Place the unit on a flat, clear area. Firmly grasp throttle grip with left hand and rapidly pull recoil starter handle/rope (E) until engine fires. IMPORTANT Recoil starter: Use short pulls - only 1/2 ~ 2/3 of rope for starting. Do not allow the rope to snap back in. Always hold the unit firmly. NOTE If engine does not start after 5 pulls, use Cold Start Procedure. E C E B A D 13 POWER BLOWER OPERATOR'S MANUAL STOPPING ENGINE 1. Throttle Trigger/Throttle Position Lever Release throttle trigger (F). Move throttle position lever (B) forward to idle position and allow engine to return to idle before shutting off engine. 2. Stop Switch Move stop switch (A) to “STOP” position. WARNING If engine does not stop when stop switch is moved to STOP position, close choke - COLD START position - to stall engine. Have your ECHO dealer repair stop switch before using blower again. F OPERATING BLOWER WARNING Always wear safety glasses, hearing protection and a face filter mask or serious personal injury may result. Do not point the blower pipe in the direction of people or pets. Read the Safety Section carefully. IMPORTANT To avoid engine damage due to over-revving, do not block blower pipe. 1. Use only during appropriate hours. 2. Allow the engine to warm up at a fast idle for a few minutes. 3. Control engine speed with throttle trigger (F), or for continuous use, set engine speed with throttle position lever (B). Rotate throttle position lever forward for lower speed, back for higher speed. 4. Use lower speed to blow debris from hard surfaces. 5. Additional speed may be necessary to clean debris, snow, etc. from lawns and flowerbeds. NOTE Never use a higher speed setting than necessary to perform a task. Remember, the higher the engine speed, the louder the blower noise. Minimize dust by using blower at lower speeds. Keep debris on your property. Be Smart - be a good neighbor. B A B F 14 MAINTENANCE Your ECHO blower is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your blower achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If task is not listed, see your ECHO Dealer for repairs. SKILL LEVEL Level 1 = Easy to do. Most requird tools come with unit. Level 2 = Moderate difficulty. Some specialized tools may be required. Level 3 = Experience required. Specialized tools are required. Echo recommends that the unit be returned to your ECHO dealer for service. ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier. Just below each task heading are listed the various part numbers required for that task. See your ECHO dealer for these parts. MAINTENANCE INTERVALS COMPONENT/ SYSTEM MAINTENANCE PROCEDURE REQ'D SKILL LEVEL DAILY OR BEFORE USE EVERY REFUEL 3 MONTHS OR 90 HOURS 6 MONTHS OR 270 HOURS YEARLY Recommended Echo Dealer Maintenance Procedures Cylinder Exhaust Port Inspect/Clean/Decarbon 3 I / C Do-It-Yourself Maintenance Procedures Air Filter Inspect/Clean/Replace 1 I / C R* Choke Inspect/Clean 2 I / C Fuel Filter Inspect/Replace 1 I R* Fuel System, Leaks Inspect/Replace 1 I I / R* Cooling System Inspect/Clean 2 I / C Muffler Spark Arrestor Inspect/Replace 2 I / R* Recoil Starter Rope Inspect/Clean 1 I / C I / R* Spark Plug Inspect/Clean 2 I / C R* Screws/Nuts/Bolts Inspect/Tighten/Replace 1 I / R* MAINTENANCE PROCEDURE LETTER CODES CLEAN=REPLACE, C=INSPECT, R=: I -IMPORTANT NOTE Actual use and your experience will determine the frequency of requiredTime intervals shown are maximum. maintenance. MAINTENANCE PROCEDURE NOTES: * All recommendations to replace are based on the finding of damage...