Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
• Provide all operators of this equipment with the Operator's Manual and instructions for safe operation. • Do not point blower at people or animals. • Start unit on ground with throttle at idle. Check that blower pipe is not blocked by the ground or by any objects. WARNING DANGER Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Keep A Firm Grip • Hold handle with fingers together encircling the handle. Keep A Solid Stance • Maintain footing and balance at all times. Do not stand on slippery, uneven or unstable surfaces. Do not work in odd positions or on ladders. • Do not perform Maintenance or Assembly procedures with engine running. Noise Control • Follow local noise regulations on sound levels and hours of operations. Use only during appropriate hours. • Never use a higher speed setting then necessary to perform a task. The higher the engine speed the louder the blower noise. • Be a good neighbor. Avoid Hot Surfaces • During operation, the muffler or catalytic muffler and surrounding cover may become extremely hot. Avoid contact during and immediately after operation. Always keep exhaust area clear of flammable debris. Allow the engine and muffler to completely cool before performing any maintenance activity. EMISSION CONTROL EPA Phase II The emission control system for this engine is EM (Engine Modification). An Emission Control Label is located on the unit. (This is an EXAMPLE ONLY, information on label varies by engine FAMILY). IMPORTANT ENGINE INFORMATION ENGINE FAMILY: 1EHXS.0635RA DISPLACEMENT: 63.3 CC THIS ENGINE MEETS U.S. EPA PAHSE II EMISSION REGULATIONS FOR S.O.R.E. REFER TO OWNER'S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS. EMISSION COMPLIANCE PERIOD : 300 HRS. PRODUCT EMISSION DURABILITY The 300 hour emission durability period is the time span selected by the manufacturer certifying the engine emissions output meets applicable California emissions regulations, provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual. IMPORTANT This spark ignition system complies with Canadian ICES-002. POWER BLOWER OPERATOR'S MANUAL DESCRIPTION CONTENTS 1 - Power Head 1 - Flex Pipe 1 - Pipe w/swivel 1 - Straight Pipe 1 - Straight Pipe 1 - Operator's Manual 1 - Warranty Registration Card 1 - ECHO Emissions and Warranty Statement 1 - Plastic Bag 2 - Clamps w/screws 1 - Stick Handle 1 - Bolt 6x45 1 - Washer 6 1 - Wing nut 1-Bottle ECHO 2-Stroke Oil Mix 1 2 3 4 5 6 7 8 9 10 11 12 13 POWER BLOWER OPERATOR'S MANUAL DESCRIPTION CONTENTS 1 - Power Head 1 - Flex Pipe 1 - Pipe w/swivel 1 - Straight Pipe 1 - Straight Pipe 1 - Operator's Manual 1 - Warranty Registration Card 1 - ECHO Emissions and Warranty Statement 1 - Plastic Bag 2 - Clamps w/screws 1 - Stick Handle 1 - Bolt 6x45 1 - Washer 6 1 - Wing nut 1-Bottle ECHO 2-Stroke Oil Mix 1 2 3 4 5 6 7 8 9 10 11 12 13 1. SPARK PLUG -Provides spark to ignite fuel mixture. 2. SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -The muffler or catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler. Keep exhaust area clear of flammable debris. 3. RECOIL STARTER HANDLE - Pull recoil handle slowly until starter engages, then quickly and firmly. When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur. 4. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carburetor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. 5. CHOKE -Move lever UP to close choke (starting position) and for emergency stopping. Move DOWN to open choke (run position). 6. FUEL TANK- Contains fuel and fuel filter. 7. FUEL TANK CAP -Covers and seals fuel tank. 8 8 AIR CLEANER -Contains replaceable air filter element. 9. BLOWER PIPES -Twist lock design. 10. THROTTLE POSITION LEVER/STOP SWITCH -Combination stop switch and variable speed throttle lever. When the lever is moved all the way forward the blower is at Wide Open Throttle (W.O.T.). When the lever is moved rearward to detent, the blower is at idle. When the lever is moved rearward past the idle detent the blower will stop. 11. SAFETY DECAL -Lists important safety precautions. 12. HANDLE -Rotates downward for throttle control access. Spring loaded for flexible operation. 13. SHOULDER HARNESS -Used to support unit on operator's back. The straps are adjustable. ASSEMBLY SPECIFICATIONS MODEL PB-650 Length 375 mm (14.76 in.) Width (19.1 in.)485 mm Height 527 mm (20.75 in.) Weight (dry) kg (23.0 lb.)10.4 Engine Type Air cooled, two-stroke, single cylinder gasoline engine Displacement 63.3 cc (3.86 cu. in.) Bore 48.0 mm (1.89 in.) Stroke 35.0 mm (1.38 in.) Carburetor Walbro Diaphragm, model WYK w/primer bulb Ignition S...
Este manual também é adequado para os modelos :Sistemas de ventilação - PB-403 (1.12 mb)
Sistemas de ventilação - PB-413 (1.12 mb)
Sistemas de ventilação - PB-603 (1.12 mb)
Sistemas de ventilação - PB-650 (1.12 mb)