Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Battery charging 1. Connect charger (5) to power source. The green light (a), should light up. This indicates the charger is ready to begin charging. 2. Position battery pack on charger, align rails (d), on battery charger with (e) on battery pack. Slide battery forward onto charger until it clicks into position. 3. The red light (b), should begin to glow continuously, indicating that the battery pack is receiving a “Fast Charge”. 4. After approximately one hour, the “Fast Charge” indicator red light (b) should go out indicating that the battery pack is fully charged and that the charger is now in a “Maintenance Charge” mode, this is confirmed by the light (a) coming back on. The battery pack can be left on “Maintenance Charge” until you are ready to use it, however it is not recommended to leave the battery on charge for longer that 24 hours. 5. To remove the battery pack from the charger depress the battery pack release tabs (4) and slide the battery off. WARNING. Do not leave batteries charging for longer than 24 hours. Note. Depending on room temperature, line voltage, and existing charge level, initial battery charging may take longer than one hour. NOTE. Disconnect charger from power source when not in use. To obtain the best life for the battery • Never allow the drill to come to a complete stand still before recharging. The battery should be placed on charge whenever the battery is noticeably running down or the drill no longer performs a task it previously performed. • Avoid conducting short charges. Make sure that the battery is fully charged every time by allowing the charger to complete its full charging cycle. • Avoid allowing lose items like screws or nails etc to be stored with battery packs as these or similar items can short battery packs and cause a fire or explosion. • Always unplug the charger when not in use and store in a dry secure place. • Avoid charging or storing your battery in temperatures below 0.C and above 40.C. b a d e Attaching the blower tube CAUTION. Always ensure that the tool is switched off and the battery is removed before making any adjustments or maintenance procedures. Slide the blower tube (2) onto the blower housing, ensuring the hole in the tube matches up with the raised section in the housing. Turning the blower on and off 1. Ensure the battery pack (3) is inserted. 2. To switch on squeeze the trigger switch (1). 3. To switch off, release the trigger switch. Operation of the blower Hold the blower firmly and rotate from side to side, holding the tube several inches above the ground. Slowly move forward directing the debris to the desired location. • Prior to using the blower, ensure you have read and understood this instruction manual. • Ensure you are wearing suitable clothing and also safety equipment like safety glasses, ear protection and a mask if necessary. • Ensure the attachments to the blower are correctly fitted and adjusted. • Be aware of other people and animals in the area where you are to be operating the blower. Tips for using your blower The following points may assist you in the operation of the blower. • Always try and blow dry leaves, cuttings or general garden debris, wet material is difficult to move. • If the leaves etc. are damp, then use the blower to pile the leaves etc. into one area for collection. Maintenance and storage information Prior to cleaning or any maintenance, always ensure the battery pack has been removed from the tool. When you have finished using the blower, always check to make sure the product is clean and free of dirt and debris. Do not use solvents to clean the blower. Store the blower in a dry place, and out of reach of children. Carefully read the entire Instruction Manual before using this product. Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: • GMC Product Type • GMC Product CodeA GMC Service Engineer will take your call and, in most cases, will be able to solve your problem over the phone. You are welcome to use this phone-in service to make suggestions or give comments about any GMC product. With continuing product development changes may have occurred which render the product received slightly different to that shown in this instruction manual. The manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country to country. The GMC 777 Helpline operates from 7am to 7pm, 7 days a week (EST). This allows you to contact GMC directly with any queries and technical questions you have regarding our products. 45–55 South Centre Road Melbourne AirportVictoria, Australia 3045Tel: (03) 8346 1100 Fax: (03) 8346 1200Save this Manual for future reference. ...
Este manual também é adequado para os modelos :Sistemas de ventilação - CBL18 (930.49 kb)