Assessments - 5, GPA: 3.6
(
)
)
|
Facilidade de uso
If fuel must be stored longer than 30 days, it should first be treated with a stabilizer or similar product. Operation Choke control If the engine is cold you will need to use the choke control. Start position (choke closed). Run position (choke open). Starting the blower To start the engine, proceed as follows: 1. Press the primer (9) 5 to 6 times until there are no air bubbles are visible in the fuel discharge line. Note. This is not necessary if the engine is warm. 2. If the engine is cold, move the choke (15) lever upwards closed. Note. Again this is not necessary if the engine is warm. 3. Place the blower on the ground, and hold the blower handle firmly with your right hand. 4. Pull the recoil starter (6) until the engine sounds like it wants to run. 5. Push the choke all the way down. 6. Pull the recoil starter rapidly until the engine starts. 7. Allow the engine to run for 10 seconds to let it warm up. 8. To increase the engine speed squeeze the throttle trigger (1). Stopping the blower Stop the engine by pressing the off button (12) and holding it for 2 seconds. Blowing Start the blower engine, as previously described. Hold the blower firmly about 10 - 20 cm from the ground and move it in a sweeping motion from left to right, directing the debris to the desired location. • Use low throttle settings when clearing lightweight materials from around lawns or shrubbery. • Use medium to higher throttle settings to move lightweight grass or leaves from driveways or paths. • Use full throttle when moving heavy loads such as dirt or snow. IMPORTANT. Blower noise increases at higher throttle settings. Always use the lowest throttle setting required to get the job done. • Never operate the blower unless it is properly assembled and in good working condition. • Never operate the blower without a properly functioning muffler and spark arrestor installed. Use of the petrol blower • The GMC petrol blower can efficiently move a wide variety of debris ranging from grass clippings to gravel. As a general rule try to operate the blower at the lowers throttle setting necessary to get the job done. • Prior to use of the blower ensure you have read and understood this instruction manual. • Ensure you are wearing suitable clothing and also safety equipment like safety glasses, ear protection and a mask if necessary. Maintenance WARNING. Before performing any maintenance on this blower, stop the engine and disconnect the spark plug wire. Checking the spark plug Check the spark plug every 10 - 15 hours of use. Note. There is a replacement spark plug included with the blower. 1. Remove the spark plug cover. 2. Use the spark plug wrench to remove the spark plug, by turning it counter-clockwise. 3. Clean and adjust the spark plug gap to 0.6 - 0.7mm. Replace any damaged or visibly worn plug with a CHAMPION RCJ6Y, NGK BPM9A or equivalent spark plug. 4. Install the spark plug finger tight in the cylinder head, then tighten it firmly with the spark plug wrench. Air filter The air filter should be checked approximately every 10 hours of use, or more frequently in dusty areas. 1. Loosen the air filter cover retaining screw (16), and remove the cover and filter element. 2. Inspect the element. If the element is distorted or damaged, replace it with a new one. 3. Wash the filter in detergent and water. Rinse the filter thoroughly. Squeeze out excess water. Allow it to dry completely before reinstalling. 4. Install the element and cover and then tighten the retaining screw. Servicing • It is recommended once you first use your petrol blower have it serviced after 15 hours of use. • From thereafter, service the petrol blower every 2 years. Storage and maintenance after use • When you finish working, clean the petrol blower completely. • Inspect the entire blower and tubes for damage, including loose or missing components, and repair anything necessary. • Store the petrol blower away from direct sunlight. • Do not store in a nylon bag as this can encourage the formation of mould. • Use a small brush to clean off the outside of the unit and keep the air vents free from obstructions. Do not use water or a hose to clean the unit. Whenever the machine is not used for a long period of time, proceed as follows: • Give the petrol blower an overall cleaning and a thorough check. • Empty the fuel tank completely, then clean the carburetor and lines by running the blower until it stops from lack of fuel. • Protect all metal engine parts from corrosion by coating them with oil. • Remove the spark plug, put several drops of oil into the cylinder through the spark plug hole and then pull the recoil starter 2 to 3 times in order to distribute the oil evenly. Replace the spark plug and spark plug cover. • Clean the air filter as described in the air filter section. Problems Power loss or sudden stopping of the engine • Check whether the fuel tank is empty. • There is water in the mixture. Drain and rinse the fuel system with petrol. • The air filter is...
Este manual também é adequado para os modelos :Sistemas de ventilação - PB26D (970.66 kb)