Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
• Always start by filling half the quantity of petrol required. Then add the entire oil quantity. Mix (shake) the fuel mixture. Fill the remaining quantity of petrol. • Mix (shake) the fuel mixture carefully before filling in the machine‘s fuel tank. • Do not mix more than max. one month’s supply of fuel. • If the machine is not used for a long period of time, the fuel tank should be emptied and cleaned. ! ! WARNING! The catalytic converter muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when handling the saw near flammable substances or vapours. Fuelling 5 10 15 20 2% (1:50) 0,10 0,20 0,30 0,40 3% (1:33) 0,15 0,30 0,45 0,60 Gasolin Benzin Essence Gasolina Lit. Oil • Ol Huile • Aceite Lit. 1 2 1/2 5 2% (1:50) 2 1/2 6 1/2 12 7/8 3% (1:33) 3 3/4 9 3/4 19 1/4 US gallon US fl. oz. ! ! WARNING! The following precautions reduce the risk of fire: Do not smoke or place any sources of heat in the vicinity of the fuel. Never refuel when the engine is running. Always stop the engine and let it cool for a few minutes before refuelling. Open the fuel cap slowly when fuelling so that any over pressure is released slowly. Tighten the fuel cap carefully after refuelling. Always move the machine from the fuelling place before starting. • Clean around the fuel cap. Contamination in the tank can disrupt operations. • Ensure that the fuel is well mixed by shaking the container before filling the tank. Min. 3 m (10 ft) 12 – English STARTING AND STOPPING ! ! WARNING! Never start the blower if the inspection cover is not closed, is damaged or cannot be closed. (Exception: When the vacuum tube is fitted). Starting a cold engine A cold engine should be started in the following manner: 1. Move the stop switch to the start position. 2. Set the choke to the choke position. Setting the chock will automatically set the throttle damper to the start throttle position. IMPORTANT! Do not pull out the starter cord completely and do not release the starter handle from the fully pulled out position. Doing so will damage the starter 3. Press the blower against the ground and pull the starter handle slowly until resistance is felt (when the starter pawls engage). Then pull it with quick, vigorous movements. 4. Move the choke control back immediately when the engine ignites and proceed according to item 3 above. 5. When the motor starts, rapidly give it full throttle. The throttle latch will then automatically disengage. Starting a warm engine A warm engine can be started in the same manner as a cold engine, but with the following exception: Set the throttle to the start position by first moving the choke forward, and then back again. The choke should not be used when the engine is warm. Stopping The engine is stopped by switching off the ignition. Move the stop switch to the stop position.. English – 13 USING THE BLOWER To blow away debris on theground Fitting the blower tube and nozzle on the blower ! ! WARNING! When fitting the blower tube and nozzle, the engine must be switched off and the stop switch must be in the stop position. The blower tube and nozzle have a bayonet mount. Fit them in the following manner: 1. Press the blower tube (15) against the blower air outlet and turn it 90 degrees until a snap is heard. 2. Fit the nozzle (14) onto the tube (15), and turn it 90 degrees until a snap is heard. Blowing Before you begin blowing, put on the required safety equipment. ! ! WARNING! When working with the blower, wear the required protecting equipment: 1. Hearing protection. 2. Eye protection. 3. Face mask in dusty environments. When operating the blower, the blower must be secured to the shoulder strap. The strap should be worn over the shoulder as shown in the adjacent figure. 15 14 14 – English USING THE BLOWER ! ! WARNING! Never point the blower nozzle at people or animals. The high-velocity air stream can contain particles that may cause serious injury, especially if the blower has previously been used for vacuuming. Be careful, particurlarly if left hand operation is applied. Avoid any direct body contact with the exhaust outlet area. WARNING! WARNING! Never start the blower if the Do not operate the blower while ! ! inspection cover is not closed, is standing on a ladder or a stand. damaged or cannot be closed. (Exception: When the vacuum tube is fitted). Start the blower as described on page 13. Work according to the following instructions: 1. Never blow air toward fixed objects such as walls, large rocks, automobiles and fences. 2. When working inside corners, blow from the corner and inward toward the centre of the work area. Otherwise, debris can fly up in your face and cause eye injury. 3. Never point the blower nozzle at delicate plants. High-velocity nozzle (21) The high-velocity nozzle is an accessory of the blower and is not included in the standard supply. When blowing with greater accuracy and high air stream concentration is necessary, substitute the st...