Assessments - 6, GPA: 4.2 ( )

Fabricante : Husqvarna Arquivo Tamanho: 5.05 mb Arquivo Nome : HOUS2008_1150983-95.pdf Língua de Ensino:

. . . . . . . . . . . . . . . . . . . . . . . .17CONTROL ARM [150BF/170BF/180BF] . . . . . . 17 STARTING ENGINE. . . . . . . . . . . . . . . . . . . . . .17 ADJUSTING IDLE SPEED. . . . . . . . . . . . . . . . . 18 STOPPING ENGINE . . . . . . . . . . . . . . . . . . . . .18 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 AIR CLEANER . . . . . . . . . . . . . . . . . . . . . . . . . .19 FUEL FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . .20 SPARK PLUG. . . . . . . . . . . . . . . . . . . . . . . . . . .20 MUFFLER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 SPARK ARRESTER. . . . . . . . . . . . . . . . . . . . . .20 AIR INLET NET . . . . . . . . . . . . . . . . . . . . . . . . .21 IGNITION COIL AIR GAP INSPECTION . . . . . . 21 SHOLDER STRAP. . . . . . . . . . . . . . . . . . . . . . .21 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 English Safety SAFETY FIRST Instructions contained in warnings within this manual and warning seals marked with a symbol on the blower concern critical points which must be taken intoconsideration to prevent possible serious bodily injury, and for this reason you are requested to read all suchinstructions carefully and follow them without fail. Notes on types of warnings WARNING Instructions labeled as shown above, concern critical steps or procedures which must be followed in order to prevent accidents which could lead to serious bodily injury or death.This mark isused to indicate instructions which must be followed without exception. IMPORTANT Instructions labeled as shown above concern steps or procedures which, if not followed correctly, could lead to mechanical failure, breakdown, or damage. NOTE Used to label supplementary instructions designed to provide hints or directions useful in the use of the product. Warning labels on the machine Symbols The blower operator mustmake sure that no WARNING! The machine can bystanders or animals come be a dangerous tool if used nearer than 50 feet (15incorrectly or carelessly, which meters). Whenever several can cause serious or fatal injury operators are working in the same work area, theyto the operator or others. should maintain a safe distance of at least 50 feet (15 meters) from one another. A breathing mask should be usedcarefully and make sure you Please read the operator’s manual when there is a risk of dust. understand the instructions before using the machine. Keep all parts of your body away Always wear: from hot surfaces. • Hearing protection • Approved eye protection Always wear protective gloves. Other symbols/decals on the machine refer tospecial certification requirements for certain markets. IMPORTANT If the warning label peels off or becomes soiled and impossible to read, you should contact the dealer from which you purchased the product to order new labels and affix them in the required location(s). Wear study, non-slip boots The blower can forcibly throw objects that can bounce back. This can result in serious eye injuries if therecommended safety equipment is not used. English 5 For safe operation and maintenance, symbols are carved in relief on the machine. Using to these indications, please be careful not to make a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: INTAKE CUP (c) The direction to open the choke Position: INTAKE CUP (d) The direction to stop the engine Position: THROTTLE LEVER [130 BT/150 BT/170 BT only] (e) The emission information label .1 : THE ACTUAL MANUFACTURING MONTH WILL BE PRINTED. .2 : THE INITIAL NUMBER WILL BE CHANGED EVERY YEAR OF MANUFACTURING. This engine label certifies that the product is certified in accordance with American exhaust emissions requirements EPA Ph II and CARB Tier III. The Emissions Compliance Period referred to on the emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal and California emission requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours. For customer assistance call: 704-921-7000 or contact us at our website: IMPORTANT Check the emission information label on your product. In the case of , the product is unsupported to use in California. WARNING 1. Read this Blower Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury. 2. Be sure to keep this manual handy so that you may refer to it later whenever any questions arise. Also note that you are requested to contact the dealer from whom you purchased the product for assistance the event that you have any questions which cannot be answered herein. 3. Always be sure to include this manual when selling, lending, or otherwise transferring the ownership of this product. 4. Do not lend or rent your machin...

Baixe o seu

Para fazer o download, introduza 2 dígitos :