Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
WARNING: To prevent accidental starting that could cause serious personal injury, always disconnect the engine spark plug wire from the spark plug when assembling parts. WARNING: Disconnect the spark plug wire before assembling parts. Failure to do so could result in possible serious personal injury. assembling the blower tubes See Figures 3 - 5. n Place a tube clamp in the groove on elbow and install the elbow tube onto blower. Tighten large clamp securely. n Place clamp in the groove on the bellows and install the bellows onto the elbow. Tighten clamp securely. . Insert upper tube into adjustable handle. Position the adjustable handle in the center of upper tube and tighten thumb screw securely. NOTE: The position of the adjustable handle may be moved for the best comfort after the blower is strapped onto the operator’s back. n Place clamp in the groove on the bottom end of the bellows and install the upper tube onto the bellows. Tighten clamp securely. . Join the lower tube and nozzle together by aligning raised locking tabs on lower tube with the raised locking slots on nozzle and twist to secure. . Assemble the connected lower tube and nozzle to the upper tubes by aligning raised locking tabs on the upper tube with the raised locking slots on connected lower tubes by twisting to secure. NOTE: Check all locking connections to ensure they are tightly secured. CAUTION: Make all adjustments to the harness straps before starting the blower to avoid the possibility of injury. ADJUSTING HARNESS and waist STRAPS Straps should be adjusted to a comfortable position before starting the blower. To adjust harness strap assembly: . Blower should be in operating position before adjusting the harness straps. Slip arm through harness strap and onto shoulder, then repeat for the other shoulder. . There are three possible height adjustment positions that can be used to easily adjust harness. . Slip top buckle of harness from adjustment slot and position to desired height location. . Tighten (pull down on strap) or loosen (lift up on tab of strap buckle) each harness strap as needed, until each is adjusted to a comfortable operating position. . Chest strap should be tightened or loosened until adjusted to a comfortable operating position. To adjust waist strap assembly: . Waist strap should be tightened or loosened until adjusted to a comfortable operating position. ADJUSTING ADJUSTABLE handle See Figure 6. . Loosen thumb screw by twisting counterclockwise. . Move adjustable handle to desired position and secure screw by twisting clockwise. OPERATION WARNING: Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this product for the purposes listed below: . Clear leaves and other debris from your lawn . Keeping decks and driveways free from grass clippings, leaves, pine needles, and other debris FUELING AND REFUELING the blower FUEL MIXTURE This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded gasoline and 2-cycle engine lubricant in a clean 1 gallon container approved for gasoline. Recommended fuel: This engine is certified to operate on unleaded gasoline intended for automotive use. Mix a high quality 2-cycle engine lubricant at 2.6 oz. per gallon (US). Do not use automotive lubricant or 2-cycle outboard lubricant. DO NOT mix quantities larger than usable in a 30 day period. high quality 2-cycle engine lubricant Gasoline lubricant 1 gallon (US) 2.6 oz. 1 liter 20 cc (20 ml) FILLING TANK . Clean surface around fuel cap to prevent contam- ination. . Loosen fuel cap slowly. Rest the cap on a clean surface. . Carefully pour fuel into the tank. Avoid spillage. . Prior to replacing the fuel cap, clean and inspect the gasket. . Immediately replace fuel cap and hand tighten. Wipe up any fuel spillage. NOTE: It is normal for smoke to be emitted from a new engine after first use. WARNING: Always shut off engine before fueling. Never add fuel to a machine with a running or hot engine. Move at least 30 ft. from refueling site before starting engine. Do not smoke! Failure to heed this warning could result in serious personal injury. OXYGENATED FUELS Some conventional gasolines are blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If using an oxygenated fuel, make sure it is unlea...
Este manual também é adequado para os modelos :Sistemas de ventilação - RY09701 (3.29 mb)