Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
The mo tube with the grooves on the blower tor must be stopped and the impeller outlet. blades no longer turning to avoid serious injury from the rotating blades. 2. Pushthebloweronto tubethe bloweruntilinto outletitsnaps place(tubebyredtube issecured release button). 3. Toremovetube,the theblowerpress tubereleasewhileon buttonpulling tube. {/_Tube Release Button \('_'_, b,// Blower Tube _w_ er outlet VACUUM ASSEMBLY NOTE: Assembly instructions for using your unit as a blower are explained in the previous section. If you have already assembled your unit for use as a blower, remove the blower tube. CAUTION: To avoid causing damage to the unit, DO NOT attempt to use the variable speed control during vacuum use. Remove the inlet restrietor An inlet restrictor is used when using your unit as a blower. This restrictor is not used during vacuum use and must be removed during assembly for vacu um use. NOTE: Be sure to keep the inlet restrictor for using your unit as a blower. 1. Ensure unit is stopped and extension cord is unplugged. 2. Open the inlet cover by inserting the tip of a screwdriver into the latch area on the blower unit. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand. Bottom view _ Latch Area Vacuum Inlet Cover (closed) Impelle Latch Area Vacuum' nlet Cover (opened) 3. Turn the inlet restrictor counterclockwise and remove it from the unit. Do not close the inlet door. You will next attach the vacuum tubes. Vacuum } Inlet Restdctor Attaching the vacuum tubes There are 2 vacuum tubes, an upper tube and a lower tube. The upper tube has a vacuum assist handle attached to one end and is cut straight on both ends. The upper tube attaches to the blower unit. The lower tube has an angled end that you point toward the ground during vacuum use. The lower tube attaches to the upper tube. 1. Ensure unit is stopped and extension cord is unplugged. 2. While holding inlet cover open, place the hooks of the vacuum assist handle on the retaining posts of the unit. 3. Raise the tube until it is secured to the blower unit by the red inlet cover latch. _k vUarmV,_cuiu PuPetHTUn°cte !_._ Retaining Post 4. To attach the lower vacuum tube to the upper vacuum tube, first align the arrows on the two tubes. Then, press the two tubes together until the lower tube is securely seated in the upper tube (about 3 inches). z_._4 Upper Tube Lower Tube it arrowsuppe oe d,owertubes COLLECTION BAG ASSEMBLY 1. Open the zipper on the collection bag and insert the elbow tube. 2. Push the small end of the elbow tube through the small opening in the bag. NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube and the hole for the tube release button is on top. 6 HOW TO CONVERT UNIT FROM Elbow Tube Tube ReleaseVACUUM USE TO BLOWER USE Button 1. Stop unit and unplug the extension Hole cord. 2. Remove the vacuum tubes by inserting the tip of a screwdriver into the latch area on the vacuum assist han- Zipper _1 dle. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vac- Opening Opening 3. Close the zipper on the bag. Make uum assist handle with your other sure the zipper is closed complete-hand. ly. Latch Area tube with the grooves on the blower outlet. 4. Align the grooves on the elbow 5. Push the elbow tube onto the blower outlet until it snaps into place (elbow tube is secured by red tube release button). ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG 1. Carefully loop the shoulder strap 3. Install the inlet restrictor that was through the buckle as shown in the illustration below. removed when assembling for vac uum use. NOTE: If you are unable to locate the inlet restrictor, the unit will still operate. Last Int_ This restrictor improves the blower function. 4. Remove the collection bag. 5. Close the inlet cover and make sure it is latched closed. 6. Re-install the blower tube. Refer to 2. Position the unit on your right-hand Aqq-AOHtNGTHE BLOWER TUBE for side, blower outlet and bag pointing instructions on how to attach this toward the rear. Hold the unit in an item. upright position with the lower vacu um tube on the ground to support it. SELECT AN EXTENSION CORD 3. Place the shoulder strap over your Use only a 120 A.C. voltage supply as head and onto your left shoulder. shown on nameplate of the unit to 4. Adjust the strap to allow a free flow power your blower. of air from the blower. If the collec- The extension cord used to reach the tion bag is kinked, the unit will not power source must be: operate properly. NOTE: The strap is designed to posi • Specifically marked as suitable for outdoor use. The cord must be marked tion the collection bag on your shoulder with the suffix WV-A" (in Canada "W")= without kinks. The strap is not intended to support the weight of the unit. • Heavy enough to carry full current from the power source to the un...
Este manual também é adequado para os modelos :Sistemas de ventilação - 358.748260 (1.02 mb)