Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
_!_WARNING: Stop the unit and disconnect from the power source before opening the inlet cover or attempt ing to insert or remove the inlet restrictor, blower tube, or vacuum tubes. The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades. zl, ____.__ 4_b,WARNING: If received assembled, ensure your unit is properly assembled and all fasteners are secure. • A standard screwdriver is required for assembly. • Alwaysusebegshoulthecollection derstrapwhentoavoid vacuuming lossofcontrol. • Checkairintakeelbow openings,tube, andvacuumfrequently, tubesalways withtheunitstopped andthepower sourcedisconnected.vents Keepand tubesfreeofdebriswhichcanaccu mulateandrestrictproperairflow.Do notusewithanyopeningblocked, Keepfreeofdust,lint,hairandany thingthatmayreduceairflow. STANDARDS This product is listed by Underwriters Laboratories, Inc., in accordance with UL Standard 1017. 1-800-235-5878. Failure to follow all Safety Rules and Precautions can result in serious injury. INSTRUCTIONS BLOWER ASSEMBLY NOTE: Assembly instructions for using your unit as a vacuum follow this section. Attaching the blower tube If you have already assembled your unit for use as a vacuum, refer to the section HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE. TO attach blower tube: 1. Align the grooves on the blower tube with the grooves on the blower outlet. 2. Push the blower tube onto the blower outlet until it snaps into place (tube is secured by red tube release button). 3. To remove the blower tube, press the tube release button while pulling on tube. _Tube Release Button \ ( --\/ _ Blower Tube Blower outlet 5 VACUUM ASSEMBLY NOTE: Assembly instructions for using your unit as a blower are explained in the previous section. If you have already assembled your unit for use as a blower, remove the blower tube. Remove the inlet restrictor An inlet restrictor is used when using your unit as a blower. This restrictor is not used during vacuum use and must be removed during assembly for vacu um use. NOTE: Be sure to keep the inlet re- stricter for using your unit as a blower. 1. Ensure unit is stopped and extension cord is unplugged. 2. Open the inlet cover by inserting the tip of a screwdriver into the latch area on the blower unit. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand. Bottom view Latch Area of unit Vacuum Inlet Cover (closed) Latch Area Vacuum / nlet Cover (opened) 3. Turn the inlet restrictor counterclockwise and remove it from the unit. Do not close the inlet door. You will next attach the vacuum tubes. ground during vacuum use. The lower tube attaches to the upper tube. 1. Ensure unit is stopped and extension cord is unplugged. 2. While holding inlet cover open, place the hooks of the vacuum assist handle on the retaining posts of the unit. 3. Raise the tube until it is secured to the blower unit by the red inlet cover latch. Upper Vacuum Tube i___'ac uLm '_s_lst _ hale 4. TOattach the lower vacuum tube to the upper vacuum tube, first align the arrows on the two tubes. Then, press the two tubes together until the lower tube is securely seated in the upper tube (about 3 inches). 4 Upper Tube Lower Tube ......... / _'_" Align arrows on upper and lower tubes COLLECTION BAG ASSEMBLY 1. Open the zipper on the collection bag and insert the elbow tube. 2. Push the small end of the elbow tube through the small opening in the bag. NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube and the hole for the tube release button is on top. EIbow Tube Tube \ Vacuum \ri_nr_ Inlet Cover Inlet Restrictor Attaching the vacuum tubes There are 2 vacuum tubes, an upper tube and a lower tube. The upper tube has a vacuum assist handle attached to one end and is cut straight on both ends. The upper tube attaches to the blower unit. The lower tube has an angled end that you point toward the / /. Release Button Hole Zipper Opening Opening 3. Close the zipper on the bag. Make sure the zipper is closed completely. 4. Align the grooves on the elbow tube with the grooves on the blower outlet. 5. Push the elbow tube onto the blower outlet until it snaps into place (elbow tube is secured by red tube release button). 6 ADJUSTING THE SHOULDER STRAP Latch Area ON THE COLLECTION BAG 1. Carefully loop the shoulder strap through the buckle as shown in the illustration below. 2. Position the unit on your right-hand side, blower outlet and bag pointing toward the rear. Hold the unit in an upright position with the lower vacuum tube on the ground to support it. 3. Place the shoulder strap over your head and onto your left shoulder. 4. Adjust the strap to allow a free flow of air from the blower. If the collection bag is kinked, the unit will not operate properly. NOTE: The strap is designed to position the collection bag on your shoulder without kinks. The strap is not intend...
Este manual também é adequado para os modelos :Sistemas de ventilação - 358.799400 (1021.03 kb)