Assessments - 3, GPA: 4.3 ( )

Fabricante : Stihl Arquivo Tamanho: 327.76 kb Arquivo Nome : Língua de Ensino:

NOTE: The following procedure can be performed with the mower installed on the tractor, however for ease of installation, removing the mower deck is recommended Install Hook Plate 1. Remove the right side belt cover and retain taptite screws. 2. Remove the deflector, spring, and hinge assemble. Retain the hardware except for the carriage bolts. Use a hammer to drive the carriage bolts back through the deck, and discard the bolts. 3. Install the hook plate (B, Figure 1) below the stone guard using two 5/16-18 x 3/4 carriage bolts (A) and flange locknuts (D). Install the bolts from the bottom up. Install Pulley 1. Remove the right arbor capscrew, lockwasher, and washer. Discard the capscrew; retain the lockwasher and washer. 2. Install the pulley and hub assembly (D) on top of the original pulley. Secure with a new 7/16-15 x 2-1/4 capscrew (A) and original lockwasher (B) and washer (C). Torque to 55-75 ft. lbs. Figure 1. Install Hook Plate A. 5/16-18 x 3/4 Carriage Bolts B. Hook Plate C. Deck Shell D. Flange Locknuts E. Clips B C E A D D Stone Guard Stone Guard A B C D Figure 2. Install New Arbor Pulley A. Capscrew C. Washer B. Lockwasher D. Pulley and Hub Assy. 4 54”Turbo Blower Installation Instructions A BE C D A B E E F C D D C Figure 3. Install Cover & Spring Anchor A. Taptite Screw D. Roller Bar Retainer B. Spring Anchor E. New Arbor Cover Assy. C. Cover Clip Install Deflector 1. Locate the taptite screw (A, Figure 3) securing the inner right-hand belt cover spring clip (C). Remove the taptite screw (A). 2. Install the spring anchor (B) above the belt cover clip (C) and secure using the original taptite screw (A). 3. Install the new right hand belt cover assembly (E) using the original taptite screws removed in Step 1. 4. Assemble the hinge rod (B, Figure 4) and hinge bracket (F). Secure using the rod anchors (A), 1/4-20 x 5/8 capscrews (E), lockwashers, and nuts as shown. 5. Drill four 13/64” holes at the marked locations on the underside of the deflector assembly (E, Figure 5). 6. Secure the deflector (C, Figure 5) to the deflector hinge assembly (B) using four 10-24 x 3/4 truss head screws (D) and nylock nuts (A). Insert the screws from the bottom. Figure 4. Assemble Hinge A. Rod Anchors D. 1/4-20 Nut B. Hinge Rod E. 1/4-20 x 5/8 Capscrew C. 1/4” Lockwasher F. Hinge Bracket A B C D E Figure 5. Assemble Deflector A. 10-24 Locknut B. Hinge Assembly C. Deflector D. 10-24 x 3/4 Truss Head Screw E. 13/64 Holes 5 Installation Instructions 54”Turbo Blower 7. Install the new deflector and hinge assembly. Secure the front of the hinge bracket using a new 1/4-20 x 1-1/4 carriage bolt (B, Figure 6), one tapered spacer (D), lockwasher, and nut (E). Secure the back of the hinge bracket using a new 1/4-20 x 2-1/4 capscrew (A), 13/16 x 1 cylinder spacer (F), tapered spacer (D), and original lockwasher and nut (E). 8. Install the deflector spring (B, Figure 7). Attach the centered leg to the deflector arm (C). Attach the offset leg to the spring anchor (A). A B C D E E D F Tapered Spacer Figure 6. Install Deflector and Hinge Assembly A. 1/4-20 x 2-1/4 Capscrew B. 1/4-20 x 1-1/4 Carriage Bolt C. Hinge & Deflector (Deflector Removed for Clarity) D. Tapered Spacer E. Original Lockwasher and Nut F. 5/8 x 1 Cylinder Spacer A BC Figure 7. Connect Deflector Sp...

Baixe o seu

Para fazer o download, introduza 2 dígitos :