Assessments - 4, GPA: 4.8
(
)
)
|
Facilidade de uso
6. To remove the tubes, turn the knob counterclockwise to loosen the tubes; remove the tubes. --5 HIGH- --SPEED NOZZLE ASSEMBLY When greater air speed is desired, use the high- --speed nozzle. Lower Blower Tube Tab 1. Align the slots on the nozzle with the tabs on the lower blower tube. High- -Speed Nozzle Slot 2. Slide the nozzle onto the lower blower tube. 3. Turn the nozzle clockwise until a click is felt to secure the nozzle to the lower blower tube. VACUUM BAG ASSEMBLY 1. Open the zipper on the vacuum bag and insert the elbow tube. 2. Push the small end of the elbow tube through the small opening in the bag. Rib SmallOpeningZipperOpeningElbowTube NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube, and the rib on the elbow tube is on the bottom. 3. Close the zipper on the bag. Make sure the zipper is closed completely. 4. Remove blower tubes from engine. RibGroove 5. Insert the elbow tube into the blower outlet. Make sure elbow tube rib is aligned with the blower outlet groove. 6. Turn knob clockwise to secure elbow tube. VACUUM TUBE ASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. - -- 1. Insert the tip of a screwdriver into the latch 6. Align slanted end of lower vacuum tube as area of the vacuum inlet. shown. Firmly push lower vacuum tube LatchAreaBlowerOutletLatchArea Vacuum Inlet Cover 2. Gently tilt the handle of the screwdriver toward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand. 3. Hold the vacuum inlet cover open until upper vacuum tube is installed. VacuumInletCoverVacuumInletc TabSlot 5.Pushtheuppervacuumtubeintothevacuuminlet. Turnthetubecounterclockwiseuntilaclickisfelttosecurethetubetotheblowerunit. 4. Align the tabs on the inside of the vacuum inlet with the slots on the upper vacuum tube. --6 into upper vacuum tube. Slantedendoflowervacuumtube HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE 1. Remove the elbow tube and vacuum bag by turning the knob counterclockwise to loosen the elbow tube. 2. Remove the vacuum tubes by turning the tubes clockwise. 3. Close the vacuum inlet cover and make sure it is latched closed. 4. Reinstall the blower tubes (see BLOWER TUBE ASSEMBLY). SHOULDER STRAP ADJUSTMENT 1. Hold the unit as shown with the muffler side facing away from your body and clothes. 2. Pass the shoulder strap over your head and onto your right shoulder. 3. Extend your left arm toward the rear of the vacuum bag. 4. Adjust shoulder strap until the vacuum bag/shoulder strap seam lies between your thumb and index finger. 5. Make sure air flows freely from the elbow tube into bag. If bag is kinked, the unit will not operate properly. - -- OPERATIONOPERATION KNOW YOUR BLOWER READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. MULCHING BLADES Your blower is equipped with mulching blades as a standard feature. When using the vacuum attachment, the mulching blades automatically reduce debris at a ratio of up to 16:1. Upper Vacuum Tube Elbow Tube Lower Vacuum Tube STOP Vacuum BagSwitch Throttle Trigger Spark Starter Upper Blower Tube Rope High- --Speed Nozzle Fuel Mix Fill Cap Primer Button StartLeverPlugVacuumHandle Lower Blower Tube OPERATING POSITION Blower Vacuum OPERATING TIPS S While vacuuming or blowing debris, hold the unit with the muffler side facing away from your body and clothes (see OPERATING POSITION illustration above). S To reduce the risk of hearing loss associated with sound level(s), hearing protection is required. S To reduce the risk of injury associated with contacting rotating parts, stop the engine before installing or removing attachments. Do not operate without guard(s) in place. S Operate power equipment only at reasonable hours- --not early in the morning or late at night when people might be disturbed. Comply with times listed in local ordinances. Usual recommendations are 9:00 a.m. to 5:00 p.m., Monday though Saturday. S To reduce noise levels, limit the number of pieces of equipment used at any one time. --7 - - STOP SWITCH The STOP switch is used to stop the engine. To stop the engine, push and hold the STOP switch in the STOP position until the engine stops. THROTTLE TRIGGER The THROTTLE TRIGGER is used to select the desired engine speed. PRIMER BUTTON The PRIMER BUTTON removes air from the carburetor and fuel lines and fills them with fuel. This allows youtostart theengine with fewer pulls on the starter rope. Activate primer button by pressing it and allowing it to return to its original position. START LEVER The START LEVER helps to supply fuel to the engine to aid in starting. Activate the startin...
Este manual também é adequado para os modelos :Sistemas de ventilação - 115351327 (254.9 kb)