Assessments - 2, GPA: 3.5 ( )

Fabricante : Husqvarna Arquivo Tamanho: 1.87 mb Arquivo Nome : Língua de Ensino:

4. Secure with knob. Retainer Knob Outer Pulley Cover Deck Belt Shield Belt Cover Tab Middle Chute Latch 1. Temporarily secure the hold down bracket to the skid plate, using a bolt and nut from the kit and the outer hole in the bracket. If needed, prop the blower housing up so it sits vertically level, but leave no more than an 1/8" gap between the deck and blower housing. Skid Plate Back-up Plate Back-up Plate 3INSTALLING HOLD DOWN BRACKET 2. Using the back-up plate as a template, drill holes in blower housing through the slots on the hold down bracket. Drill in the middle of the bracket slots to allow for adjustment if needed. Remove hold down bracket. 3. Remove blower housing. Place back-up plate inside the blower housing, lining up new drill holes and back-up plate. Install the hold down bracket by inserting bolts from the inside, through the blower housing and into the bracket slots. Secure with flange nuts. Hold Down Bracket Hold Down Bracket Hole 10 ASSEMBLY 6TRIMMING MIDDLE CHUTE 7INSTALLING BAGGER MOUNT 1. Using the hacksaw, trim along the dashed line. 2. Locate the middle chute, flat washer, hood latch, weld nut, lock washer and machine screw from kit. 3. Install in the appropriate hole at the upper end of the middle chute, according to deck size. Trim Line Hood Latch Weld Nut Machine Screw Lock Washer Latch Location Flat Washer 7INSTALLING MIDDLE CHUTE 1. Place middle chute over the top end of the blower assembly. 2. Latch middle chute to blower assembly. Middle Chute Blower Assembly 1. Using hardware provided in kit, attach support mount to unit. 2. Attach hanger bracket to support mount. Do not fully tighten nuts at this time. Hanger Bracket 3. Secure rear end of support straps to outside of hanger assembly. Set reinforcement plates to the outside of the tank brackets and fasten front end of support strap to tank bracket and reinforcment plate with round head bolt. Secure front end of reinforcement plate to tank bracket with hex bolt. Fully secure all mounting hardware. See illustration. NOTE: Rear guard hole may need to be drilled out to 5/16" if kit hardware is too large. Support Mount Support Straps Reinforcement Plate Hex Bolt Placement Round Head Bolt Placement 11 1. Remove plastic end caps from the center bag support arm. Fully insert spacer plug into the end of the support tube. It may be necessary to tap the spacer into place with a hammer or mallet. Replace the plastic end cap back over the spacer. The additional extension will hold the hood more securely when latched. 10INSTALLING SPACER PLUGS ASSEMBLY 3. Bolt Weight Bracket Weight Plate 1. Bolt cast weight to weight brackets using 3/8-16 x 1. bolts and four nuts. 2. Slide both weight brackets over the front tube on the frame. Be sure to position the weight assembly in the center of the frame. 3. Secure with 3/8-16 x 3. bolts and four nuts. Front Tube CAUTION DO NOT operate mower with grass catcher without front weight installed. NOTE: Assistance from another person may ease mounting the cover assembly to mower. 1. Lift and rotate cover to align the cover brackets with support assembly tubes. 2. Slide the cover down over the support tubes until secure. 8INSTALLING WEIGHT KIT 9MOUNTING COVER ASSEMBLY Remove center end cap Insert spacer and replace cap OPERATION TIPS FOR IMPROVED BAGGING Follow the mower operation instructions in you mower operator’s manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total time of operation may be greater than you will experience with regular use of your grass catcher. • Always run throttle at full speed when bagging. • Select a speed low enough to give good mower cutting performance, good quality cut and good bagging performance. NOTE: It may be necessary to overlap width of cut to suit your conditions. • If grass is extremely tall, it should be mowed twice. The first time relatively high, the second time to desired height. • Use left hand side of mower for trimming. • Plastic trash bags (3.0 mil, 30 gallon) can be inserted inside grass catcher containers for ease of debris disposal. To remove the plastic trash bags when full: a. Disengage blades, shift into neutral, engage the parking brake and stop the engine. b. Unlatch and raise cover. c. Remove one container at a time by grasping container handles and pulling toward the rear, off of the tube rails. d. With the container resting on the ground, close and secure the top of the plastic lawn bag. e. Tip the container on its side and slide the filled bag from the container. f. Install a new plastic lawn bag with the edges of the bag draped over upper lip of the Container (for replacement bags refer to REPLACEMENT PARTS). g. Repeat for other container. h. Reinstall containers making sure right container overlaps left container at center supports. i. Close cover and secure latches over ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :