Assessments - 4, GPA: 3.8 ( )

Fabricante : MTD Arquivo Tamanho: 740.61 kb Arquivo Nome : Língua de Ensino:

However, it is advisable to remove the wheels and apply a small amount of light oil to each axle at least once a season. OFF-SEASON STORAGE If you are going to store your blower for any length of time (30 days or longer), it is important that the following steps be taken: 1. Drain the gas tank. Start the engine. Allow it to run out of gas. Gasoline left in the engine will leave gum deposits in the carburetor and gas tank. 2. Clean engine of all foreign matter. 3. Lubricate cylinder by removing the spark plug and pour in one ounce of clean lubricating oil through the spark plug hole into the cylinder. Crank engine slowly to spread oil and replace spark plug. To start after* storage, remove spark plug and rotate engine with starter to remove When storing any type of power equipment in an unventilated or metal storage shed, care should be taken to rust proof the equipment. Using a light oil or silicone, coat the equipment, especially springs and bearings. 6 TROUBLE SHOOTING CHART PROBLEM CAUSE REMEDY 1. Excessive vibration. A. Bent crankshaft. B. Vane plate out of balance. A. Replace crankshaft (should be done by an authorized service dealer). B. Replace vane plate. 2. Engine fails to start. A. Check fuel tank for gas. B. Spark plug lead wire disconnected. C. Faulty spark plug. A. Fill tank if empty. B. Connect lead wire. C. Clean, adjust gap or replace. See engine manual. 3. Hard starting or loss of power. A. Spark plug wire loose. B. Dirty air cleaner. A. Connect and tighten spark plug wire. B. Clean air cleaner as described in engine manual. 4. Engine overheats. A. Carburetor not adjusted properly. B. Air flow restricted. C. Engine oil level low. A. Adjust carburetor. See engine manual. B. Remove blower housing on engine and clean as described in the engine manual. C. Fill crankcase with the proper oil. NOTE: For repairs beyond the minor adjustments listed above, please contact your local service dealer. Hose Attachment Kit Model 290-204-000 is available as optional equipment. 7 Models 692, 693 eind 24695 PARTS LIST FOR LEAP BLOWER MODELS 692, 693 and 24695 REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 749-0784 Upper Handle (Painted) N 18 747-0542 Height Adjustment Crank 749-0479 Upper Handle (Chrome 19 734-1035 Wheel Ass'y. Comp. 12" x 2 726-0100 Push Nut 3/8" Rod 3" (Plastic) (Incl. 3 720-0171 Crank Knob Bearings) 4 736-0117 F I.-Wash. .385" I.D. x 734-1184 Wheel Ass'y. Comp. 10.5" .62" O.D. x 4" (Steel) 5 714-0114 Sq. Key 1/4" x 2.0" Lg * 734-1185 Tire Only (For 734-1184 6 710-0442 Hex Bolt 5/16-18 x 1.50" Wheel) Lg.* 734-1183 Rim Only (For 734-1184 7 16453 Engine Mounting Frame Wheel Ass'y- 20 736-0159 FI.-Wash. 34" I.D. x .87" 8 736-0119 L.-Wash. 5/16" I.D.* O.D. 9 712-0267 Hex Nut 5/16-18 Thd.* 21 710-0170 Hex Locking Bolt 5/16-24 10 736-0187 FI.-Wash. .63" I.D. x 1.: 5" x .62" Lg. O.D. 22 736-0162 FI.-Wash. (692 Only) 11 714-0115 Cotter Pin 1/8" Dia. x 23 736-0300 F I.-Wash. .38" I.D. x .57" O.D. 1.0" Lg. 24 750-0528 Spacer .382 I.D. x .50 12 712-0206 Hex Nut 1/2-13 Thd.* O.D. x .180" Lg. 13 736-0921 L.-Wash. 1/2" I.D.* 25 736-0169 L.-Wash. 3/8" I.D.* 14 734-1036 Swivel Caster Wheel 5" 26 712-0354 Hex Nut 3/8-8 Thd. Dia. x 1.25" 27 710-0118 Hex Bolt5/16-18x.75" Lg * 15 16273 Caster Arm Ass'y. 28 711-0797 Ferrule I 16 710-0726 Hex Wash. Hd. "AB" 29 09966 Hand Knob I Tap Scr. 5/16"x.75" l.q. 30 710-0487 Carriage Bolt 5/16-18 x 2.0" 17 14529 Caster Arm Bracket Lg. 31 749-0785 Lower Handle (Painted) N 749-0481 Lower Handle (Chrome) 8 Models 692, 693 and 24695 REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART REF. NO. PART NO. COLOR CODE DESCRIPTION NEW PART 1 14539 Engine Housing Brace Ass'y. 14 711-0758 Hex Shoulder Nut .50" I.D. 2 710-0600 Hex Self Tap Scr. 5/16" x .50" 15 14563 - 638 Nozzle Plate Ass'y. - Lg. 16 710-0191 Hex Bolt 3/8-24 x 1.25" Lg.* 3 710-0118 Hex Bolt 5/16-...

Baixe o seu

Para fazer o download, introduza 2 dígitos :