Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
• Attach the blow clamshell and tube to the powerhead (Fig. 6) by locating the blower as indicated by arrow, then pivot about this point until the locking/release catch is fully engaged. • Hold the blow tube approximately (7”) 180mm above the ground, switch your product on and using a sweeping motion from side to side, advance slowly keeping the accumulated debris/leaves in front of you (Fig. 7). • Once you have blown the debris/leaves into a pile, you can convert to vacuum mode to collect the debris. • Installing the concentrator will help remove matted debris and leaves (Fig. 8). Removing Blow/Vacuum Tube • Switch off your product and disconnect from power supply. • To disconnect the blow clamshell or vacuum tube from the powerhead, depress the release button, ensuring the tube does not fall to the ground. • The release button will not depress if the power switch is in the “on” position. (Fig. 1) Vacuum Mode • Switch off your product and disconnect from power supply. To fit the bag assembly to your product: Attach the collection bag to the vacuum outlet using the bayonet fitting, as shown in Figure 9. • Attach the vacuum assembly and tube to the powerhead (Fig. 10) by locating the assembly as indicated by arrow, then pivot about this point until the locking/release catch is fully engaged. • Position the tube slightly above the debris/leaves. Switch your product on, then using a sweeping motion the debris/leaves will be sucked up the tube, mulched and deposited into the collection bag. (Fig 11) For matted debris/leaves your vacuum tube is incorporated with a scraper. Use this scraper to loosen the debris and continue to vacuum as normal. As the bag fills the power of the suction will decrease, switch off your product and unplug from power supply. Unzip the bag to empty before continuing to operate. CAUTION: NEVER REMOVE THE COLLECTION BAG WITHOUT FIRST TURNING OFF AND UNPLUGGING THE VACUUM. NOTE: If the suction decreases and the bag is not full, the vacuum tube is probably clogged with debris. Turn off and unplug the vacuum and clear the tube before continuing. Operation • When using as a blower or vacuum, always wear safety glasses. If using in dusty conditions, wear a filter mask as well. • Do not use in vacuum mode without the vacuum tubes and collection bag in place. • Always switch off and remove the plug from the electrical supply when: • Changing from blower to vacuum. • The supply cable has become damaged or entangled. • You leave your product unattended. • Clearing a blockage. • Checking, adjusting, cleaning or working on your product. • Use your product only in daylight or good artificial light. Maintenance • CLEANING AND STORAGE TURN OFF AND UNPLUG TOOL! (Unplug extension cord at power source.) Use only mild soap and a damp cloth to clean the tool. Clean out any clippings which may have accumulated in the Blower/Vac. When used properly with dry leaves the fan chamber of your Blower/Vac should remain clean. If damp earth and debris are ingested some of the particles may build up on the inside of the fan chamber. If this happens the performance of the unit will decrease. This area can be cleaned out by gently wiping out with a damp rag after disconnecting from the power source. Your Blower/Vac should be stored in a dry place. WARNING: SHOCK HAZARD. DO NOT POUR OR SPRAY WATER ON THE TOOL IN AN ATTEMPT TO CLEAN. Do not store the tool on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts. Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. TROUBLESHOOTING Problem Possible Cause Possible Solution • Unit will not start. • Cord not plugged in. • Plug tool into a working outlet. • Circuit fuse is blown. • Replace circuit fuse. (If the product repeatedly causes the circuit fuse to blow, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.) • Circuit breaker is tripped. • Reset circuit breaker. (If the product repeatedly causes the circuit breaker to trip, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.) • Cord or switch is damaged. • Have cord or switch replaced at Black & Decker Service Center or Authorized Servicer For assistance with your product, visit our website for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986. Important To assure product SAFETY and RELIABILITY; repairs, maintenance and adjustments (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. SERVICE INFORMATION All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair,...