Assessments - 4, GPA: 3.3
(
)
)
|
Facilidade de uso
SWITCH NOTE: The switch will not operate if the release button, shown in Figure 1, is depressed. To turn the tool ON, slide the switch forward, as shown in Figure 1. To turn tool OFF, slide switch to the rear. OPERATION USE AS A BLOWER: ALWAYS WEAR SAFETY GLASSES, WEAR A FILTER MASK IF THE OPERATION IS DUSTY. USE OF RUBBER GLOVES AND SUBSTANTIAL FOOTWEAR IS RECOMMENDED WHEN WORKING OUTDOORS. FOR HOUSEHOLD USE ONLY. • BLOWER MODE - STRAIGHT TUBES ONLY Ensure that the unit is switched OFF and is disconnected from the power supply. Assemble blow tubes as shown in Figure 2 and Figure 2A. (This only needs to be done the first time you assemble the unit.) WARNING: When turning the tool off for tube installation or any other reason, wait 10 seconds for the fan to stop rotating before disassembly. Attach the blower tube assembly (The assembly includes the blower tubes, and the fan chamber) to the front of the tool, as shown in Figure 3 by inserting point A into the matching recess marked point B, also shown in Figure 3. Swing the tube up to engage the lock, as shown in Figure 4. NOTE: The lock will not engage if the ON/OFF switch is in the forward (ON) position. Hold the end of the blower tube approximately 7 inches (180mm) above the ground and turn the tool ON. Using a sweeping motion, from side to side, advance slowly keeping the accumulated debris (leaves,grass clippings etc.) in front of you, as shown in Figure 5. Once you have blown the debris into a pile, you can convert to vacuum mode to collect the debris for disposal. • BLOWER MODE - FLEX TUBE Ensure that the unit is switched OFF and is disconnected from the power supply. Assemble flex blow tube as shown in Figure 6. WARNING: When turning the tool off for tube installation or any other reason, wait 10 seconds for the fan to stop rotating before disassembly. Attach the blower tube assembly (The assembly includes the blower tubes, the flex tube, and the fan chamber) to the front of the tool by inserting point A into the matching recess marked point B, shown in Figure 3. Swing the tube up to engage the lock, as shown in Figure 4. NOTE: The lock will not engage if the ON/OFF switch is in the forward (ON) position. To attach the shoulder strap to the blower, snap the hooks at the end of the strap to the metal ring located on the top of the unit as shown in Figure 7. For right handed operation, begin with the blower behind you on your left side. Lift the blower and place the shoulder strap over your LEFT shoulder, then grasp the flex tube handle with one hand as shown in Figure 8. Sweep from side to side with the nozzle several inches above the ground. Slowly advance keeping the accumulated pile of debris in front of you. NOTE: For left handed operation, reverse the procedure above. Once you have blown the debris into a pile, you can convert to vacuum mode to collect the debris for disposal. • REMOVING THE BLOWER TUBE ASSEMBLY Switch off the unit and unplug from the outlet. To disconnect the blower tube assembly from the tool, depress the release button, shown in Figure 1, ensuring that the tube does not fall to the ground. NOTE: The release button will not depress if the ON/OFF switch is in the forward (ON) position. USE AS A VACUUM CLEANER: ALWAYS WEAR SAFETY GLASSES. WEAR A FILTER MASK IF THE OPERATION IS DUSTY. USE OF RUBBER GLOVES AND SUBSTANTIAL FOOTWEAR IS RECOMMENDED WHEN WORKING OUTDOORS. FOR HOUSEHOLD USE ONLY. •VACUUMING MODE Ensure that the unit is switched off and disconnected from the power supply. Position the vacuum tube and extension tube as shown in Figure 9. Push the extension tube into the vacuum tube until it snaps into place and the arrows shown in Figure 9A are covered as in Figure 9B. If necessary, this can be made easier by wiping the end of the extension tube with a cloth dampened with soapy water only. Attach the vacuum tube assembly (The assembly includes the extension tube, the vacuum tube and the fan chamber.) to the front of the tool. Insert point "A", shown in Figure 10, into the matching recess in the front of the tool point "B", also shown in Figure 10, and swing the tube up to engage the lock, as shown in Figure 11. Attach the collection bag to the vacuum outlet using the bayonet fitting, as shown in Figure 12. Hold the vacuum as shown in Figure 13. Tilt the vacuum tube slightly and use a sweeping action similar to the action described under Blower Mode. The light debris will flow into and through the vacuum tube into the collection bag. Things such as leaves and small twigs will be mulched as they pass through the fan chamber so that the collection bag will hold a lot of debris. When the collection bag gets full, suction will noticeably decrease. Turn off and unplug the tool and unzip the bag to empty before continuing to operate. CAUTION: NEVER UNZIP THE COLLECTION BAG WITHOUT FIRST TURNING OFF AND UNPLUGGING THE VACUUM. NOTE: If the suction decreases and the bag is not full, the vacuum tube is probably clogged with debris. T...
Este manual também é adequado para os modelos :Sistemas de ventilação - Leaf Hog BV2800 (463.1 kb)