Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Bottom view Latch Area of unit Vacuum Inlet Cover (closed) Latch Area Vacuum / nlet Cover (opened) 3. Turn the inlet restrictor counterclockwise and remove it from the unit. Do not close the inlet door. You will next attach the vacuum tubes. \ Vacuum \ ,_ _ Inlet Cover Inletri__ tube release button is on top. Restrictor Attaching the vacuum tubes There are 2 vacuum tubes, an upper tube and a lower tube. The upper tube has a vacuum assist handle attached to one end and is cut straight on both ends. The upper tube attaches to the blower unit. The lower tube has an angled end that you point toward the 6 ground during vacuum use. The lower tube attaches to the upper tube. 1. Ensure unit is stopped and extension cord is unplugged. 2. While holding inlet cover open, place the hooks of the vacuum assist handle on the retaining posts of the unit. VacuUPmPeArsV_, _UH_T: be 3. Pivot the tube until it is secured to the blower unit by the red inlet cover latch. 4. Attach the lower vacuum tube to the upper vacuum tube by aligning the arrows on the two tubes. Press the tubes together until the lower tube is fully seated in the upper tube. (About 3 inches) ube Lower Tube i"_ ........... , _'_ Align arrows on upper i_ and lower tubes COLLECTION BAG ASSEMBLY 1. Open the zipper on the collection bag and insert the elbow tube. 2. Push the small end of the elbow tube through the small opening in the bag. NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube and the hole for the Elbow Tube / L.-_J_" Zipper Opening Tube Release Button Hole Opening 3. Close the zipper on the bag. Make sure the zipper is closed completely. 4. Align the grooves on the elbow tube with the grooves on the blower outlet. 5. Push the elbow tube onto the blower outlet until it snaps into place (elbow tube is secured by red tube release button). ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG 1. Carefully loop the shoulder strap through the buckle as shown in the illustration below. Last In_,_ 2. Position the unit on your right-hand side, blower outlet and bag pointing toward the rear. Hold the unit in an upright position with the lower vacuum tube on the ground to support it. 3. Place the shoulder strap over your head and onto your left shoulder. 4. Adjust the strap to allow a free flow of air from the blower. If the collection bag is kinked, the unit will not operate properly. NOTE: The strap is designed to position the collection bag on your shoulder without kinks. The strap is not intended to support the weight of the unit. houlder strap on left shoulder No kink_ HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE 1. Stop unit and unplug the extension cord. 2. Remove the vacuum tubes by inserting the tip of a screwdriver into the latch area on the vacuum assist handle. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacuum assist handle with your other hand. Latch Area 3. Remove the collection bag. 4. Install the inlet restrictor that was removed when assembling for vacuum use. NOTE: If you are unable to locate the inlet restrictor, the unit will still operate. This restrictor improves the blower function. 5. Close the inlet cover and make sure it is latched closed. 6. Re-install the blower tube. Refer to ATTACHING THE BLOWER TUBE for instructions on how to attach this item. SELECT AN EXTENSION CORD Use only a 120 A.C. voltage supply as shown on nameplate of the unit to power your blower. • To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than the other) and will require the use of a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If plug does not fit fully into the wall outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way. The extension cord used to reach the power source must be: • Specifically marked as suitable for outdoor use. The cord must be marked with the suffix "W-A" (in Canada "W"). • Heavy enough to carry full current from the power source to the unit. Otherwise, loss of power and overheating can occur causing damage to unit. Refer to table for minimum wire gauge recommendations. The cord must be marked with the proper wire gauge. (Appropriate extension 7 cords are available.) Do not use multiple cords. • In good condition. Cord insulation must be intact with no cracks or deterioration. Plug connectors must be undamaged. DO NOT use multiple cords. MINIMUM WIRE GAUGE RECOMMENDATIONS VOLTS 25 FT. 50 FT. 1...