Assessments - , GPA:
(
)
)
Fabricante : Craftsman
Arquivo Tamanho: 2.49 mb
Arquivo Nome : e6b5d489-35c4-6834-794c-3fc2642cfc36.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
WARNING: Avoid accidental starting. Make sure you are in the starting position when pulling the starter rope (Fig. 11 and 12). To avoid serious injury, the operator and unit must be in a stable position while starting. Do not set unit on any surface except a clean, hard area while starting. Debris such as gravel, sand, dust and grass could be picked up by the air intake and thrown out by the discharge opening. This could damage the unit, property, or cause serious injury to bystanders or the operator. WARNING: STARTING INSTRUCTIONS 1. Mix gas with oil. Fill fuel tank with fuel/oil mixture. See Oil and Fuel Mixing Instructions. STOPPING INSTRUCTIONS 1. Move the throttle control to the idle position( ). Allow the engine to cool down by idling(Fig. 10). 2. Put the On/Off Stop Control in the OFF (O) position (Fig. 10). On/Off Stop Control Throttle Control Idle Fast Fig. 9 2. The On/Off Stop Control is in the ON (I) position at all times (Fig. 10). 3. Fully press and release the primer bulb 10 times, slowly. Some amount of fuel should be visible in the primer bulb and fuel lines (Fig. 10). If you can’t see fuel in the bulb, press and release the bulb as many times as it takes before you can see fuel in it. 4. Place the unit in the starting position (Fig. 11) as ablower, Fig. 12 as a vacuum). Move the throttle control to the idle position ( ) (Fig. 9). This is especially important during cold starting. Red EZ-Fire™ Lever Fig. 10 Primer Bulb Blower 5. Push the red EZ-Fire™ Lever towards the primerbulb until it clicks and locks into place (Fig. 10). NOTE: The unit uses the Incredi-Pull™ starting systemwith MAX FIRE IGNITION™, which significantlyreduces the effort required to start the engine. Youmust pull the starter rope out far enough to hearthe engine attempt to start. There is no need to pullthe rope briskly-- there is no harsh resistance whenpulling. Be aware that this starting method is vastlydifferent from (and much easier than) what you maybe used to. 6. Pull the starter rope out with a controlled and steadymotion until the engine attempts to start. Repeat untilthe engine starts. 7. When the engine starts, move the throttle control to thefast position ( ) and let the engine warm up for 15 to 30 seconds. The red EZ-Fire™ Lever will click off automatically when you move the throttle control to the fast position. IF... The engine does not start, go back to step 3. IF... The engine stops while moving the throttle, go backto step 5. IF... The engine stops before you move the throttle, movethe throttle to the fast position and pull the starteruntil the blower starts. NOTE: If you are having trouble starting the unit or areoperating in extreme temperatures (below 40. F, above90. F), refer to the Troubleshooting section. 12 To avoid serious WARNING: personal injury, always remove the vacuum bag prior torefueling the unit. The bag may become afire hazard when saturated with fuel. Fig. 11 Vacuum StartingPosition Starter Rope Fig. 12 OPERATING INSTRUCTIONS HOLDING THE BLOWER/VACUUM To avoid serious WARNING: personal injury, wear goggles or safety glasses at all times when operating this unit. Wear a face mask or dust mask in dusty locations. Before operating the unit, stand in the operating position. Check for the following: • Operator is wearing proper clothing, such as boots, safety glasses or goggles, ear/hearing protection, gloves, long pants and long sleeve shirt • If the conditions are dusty, the operator is wearing a dust mask or face mask • The unit is in good working condition • The tubes and guards are in place and secure To prevent serious WARNING: personal injury or damage to the unit, make sure blower tubes or vacuum tubes and the vacuum bag are in place before you operate the unit. • Watch out for children, pets, open windows or freshly washed cars, and blow debris safely away. • Clean up after using blowers and other equipment. Dispose of debris appropriately. OPERATING AS A BLOWER 1 Use the blower for trees, shrubs, flower beds and hard-to-clean areas (Fig. 13). 2. Use the unit around buildings and for other normal cleaning procedures (Fig. 13). 3. Use the blower around walls, overhangs, fences and screens (Fig. 14). OPERATING TIPS • Be sure the vacuum bag is zipped closed before operating the unit. • Ensure the unit is not directed at anybody or any loose debris before starting the unit. • Verify that the unit is in good working condition. Make sure the tubes and guards are in place and secure. Fig. 13 • Always hold the unit securely when operating. Keep a firm grip on both the front and rear handles. • To reduce the risk of hearing loss associated with sound level(s), hearing protection is required. • To reduce noise levels, limit the number of pieces of equipment used at any one time. • To reduce noise levels, operate power blowers at the lowest possible speed to do the job. • Check your equipment before operation, especially the muffler, air intakes and air filters. • Use rakes and brooms to loosen...