Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
This nozzle should be used when there is a need to blow in a limited or concentrated area. In general uses, such as leaf or grass blowing, the nozzle should not be used. Installing Blower Tube Install the blower tube over the blower outlet and push it on until both tabs snap into place (Fig. 1). ASSEMBLING UNIT AS A VACUUM To assemble the unit as a vacuum, begin by removing the blower tube. Refer to the previous section. Vacuum Tube Assembly NOTE: If the unit was assembled as a blower unit, remove the blower tube and store away in a secure place for later use. Installation 1. Align the small arrow on the lower vacuum tube with the arrow on the upper vacuum tube (Fig. 3). 2. Grasp the lower and upper vacuum tubes firmly with both hands, and push the lower vacuum tube into the upper vacuum tube. Turn the lower vacuum tube clockwise until it snaps into place and locks. When properly assembled, the dot on the lower tube aligns with the dot on the upper tube. 3. Place the blower/vac so that the vacuum door is facing up. Fig. 1 Fig. 3 Lower Vac Tube Upper Vac Tube ASSEMBLING THE GUTTER CLEAN-OUT ADAPTER In order to use the gutter clean-out attachment kit, you must install the gutter clean-out adapter (Part #753-05231 not included). Push the adapter onto the blower outlet until both tabs snap into place (Fig. 1). Refer to the Gutter Attachment Kit manual for more information. Arrows Tabs WARNING: To prevent serious personal injury, stop the engine and allow the impeller to stop before attaching or removing tubes. WARNING: To prevent serious personal injury or damage to the unit, the blower tube must be installed while operating this unit as a blower. WARNING: To prevent serious personal injury or damage to the unit, always install vacuum tubes and the vacuum bag, and make sure the vacuum bag is completely zipped closed when operating this unit as a vacuum. WARNING: To prevent serious personal injury, stop the engine and allow the impeller to stop before attaching or removing tubes. • When desired, insert the High Pressure Concentrator Nozzle to increase the air velocity for demanding tasks (Fig. 2). Blower Outlet ASSEMBLY INSTRUCTIONS Fig. 4 Locking Clip Vacuum Door Slot Fig. 2 Removing • Remove the blower tube by pressing both tabs at the same 4. Insert a flat head screwdriver under locking clip, lift upward time and pulling off the blower (Fig. 1). and open vacuum door (Fig. 4). 6 ASSEMBLY INSTRUCTIONS Flat Area Tabs Impeller Intake Vacuum Tube Groove Fig. 5 Align Arrows 5. While holding the vacuum door open, insert the assembled vacuum tube (put together in Step 2). Arrange the tube so the flat area faces the vacuum door. The grooves on the side of the tube will line up with the small tabs in the impeller intake (Fig. 5). From the exterior, align the small arrow on the vacuum tube with the arrow on the impeller intake. 6. Push the vacuum tube in firmly and grip it with both hands. Turn the tube clockwise as far as possible until it snaps into place and locks. When properly assembled, the dot on the vacuum tube will align with the dot on the impeller intake. Installing the Vacuum Bag 7. Install the vacuum bag adapter over the blower outlet and push on it until both tabs snap into place (Fig. 6). Position the bag so it hangs below the unit. Elbow Tabs Vacuum Bag Hook Fig. 6 8. Attach the vacuum bag to the vacuum bag hook located at the underside of the unit. 9. Keep the bag zipped and shut. Removing the Vacuum Bag 1. Unhook the bag. 2. Remove the vacuum bag by pressing both tabs on the vacuum bag elbow at the same time and pulling the bag off the blower (Fig. 6). 3. Install the blower tube in order to assemble the unit as a blower. 4. Make sure the vacuum door is securely latched shut. WARNING: Never operate the unit in the blower configuration without the vacuum door secured and latched shut. INSTALLING THE SHOULDER STRAP WARNING: To avoid serious personal injury, never attempt to start the unit when standing with the unit clipped to the shoulder strap. Always follow the starting procedures as described in the Starting/ Stopping Instructions section. 1. Push the strap through the center of the buckle. 2. Pull the strap over the cross bar and down through the slot in the buckle (Fig. 7). Fig. 7 Clip 3. Snap the clip on to the support fittings on the front or back of the handle. Clip to the front portion of the handle when using the unit as a blower, and clip to the back portion of the handle when using the unit as a vacuum (Fig. 8). Attach Here for Blowing Attach Here for Vacuuming Fig. 8 4. While standing in the operating position, adjust the length to fit the operator’s size. Pull the tab to lengthen, pull the strap to shorten (Fig. 9). 5. Do not allow the shoulder strap to dangle. Always unclip the shoulder strap from the unit when the shoulder strap is not on the operator’s shoulder. Fig. 9 7 RECOMMENDED OIL TYPE Using the proper type and weight of oil in the crankcase is extremely important. Check the oil be...