Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
If you have questions, contact the manufacturer at the addressor telephone number listed in the warranty. 2. Before servicing or cleaning unit, switch power off at servicepanel and lock the service disconnecting means to prevent powerfrom being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominentwarning device, such as a tag, to the service panel. 3. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards. 4. Sufficient air is needed for proper combustion and exhaustingof gases through the flue (chimney) of fuel burning equipmentto prevent backdrafting. Follow the heating equipmentmanufacturer’s guideline and safety standards such as thosepublished by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. 5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. 6. Ducted fans must always be vented to the outdoors. 7. To reduce the risk of fire, use only metal ductwork. 8. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected toa GFCI (Ground Fault Interrupter) - protected branch circuit. 9. Never place a switch where it can be reached from a tub orshower. 10. This unit must be grounded. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: 1. Never leave surface units unattended at high settings. Boiloverscause smoking and greasy spillovers that may ignite. Heat oilsslowly on low or medium settings. 2. Always turn hood ON when cooking at high heat or whenflambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe’). 3. Clean ventilating fans frequently. Grease should not be allowedto accumulate on fan or filter. 4. Use proper pan size. Always use cookware appropriate for thesize of the surface element. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:* WARNING 4. Use an extinguisher ONLY if: A. You know you have a Class ABC extinguisher and you alreadyknow how to operate it. B. The fire is small and contained in the area where it started. C. The fire department is being called. D. You can fight the fire with your back to an exit. * Based on “Kitchen Fire Safety Tips” published by NFPA. CAUTION ! 1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 2. To avoid motor bearing damage and noisy and/or unbalancedimpellers, keep drywall spray, construction dust, etc. off powerunit. 3. If ventilator is installed in an unconditioned space (such asan attic): Surround the ventilator with thermal insulation - to minimize possible condensation. 4. Please read specification label on product for further information and requirements. TABLE OF CONTENTS This manual is divided into sections as follows: • “TYPICAL INSTALLATION” This section shows a common installation. -Mounting (New Frame Construction) -Mounting (Existing Frame Construction) -Mounting Using Hanger Kit (included) -Ducting (Horizontal blower discharge) -Wiring • “MOUNTING OPTIONS” • “WIRING PLATE POSITION” • “DUCTING OPTIONS” -Blower Discharge Positions -Ducting (Vertical blower discharge) • “USE AND CARE” • “SERVICE PARTS” • “WARRANTY” 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metaltray, then turn off the burner. BE CAREFUL TO PREVENTBURNS. If the flames do not go out immediately, EVACUATEAND CALL THE FIRE DEPARTMENT. 2. NEVER PICK UP A FLAMING PAN - You may be burned. 3. DO NOT USE WATER, including wet dishcloths or towels - violent steam explosion will result. Installer: Leave this manual with the homeowner. Homeowner: Use and Care information on page 4. Page 2 MODELS ILB9 ! ILB11 MOUNTING USING HANGER KIT (included) Blower factory-shipped in straight-through discharge position. TYPICAL INSTALLATION DUCTING (Horizontal blower discharge) Two ways to connect ductwork to a factory-shipped unit. ROOF CAP 10” ROUND ELBOW 10” ROUND DUCT WALL CAP 8” X 12” TO 10” ROUND TRANSITIONS 10” ROUND DUCT ACCESS PANEL ACCESS PANEL SCREW GRILLE NUT (Install into square holes in housing) MOUNTING BRACKET 10” ROUND DUCT (OUTLET) 8” X 12” TO 10” ROUND TRANSITIONS 10” ROUND DUCT (INTAKE) HANGER KIT NUT & WASHER HANGER KIT BOLT & WASHER HANGER KIT CHAIN HANGER KIT EYE-BOLT TYPICAL INSTALLATION MOUNTING (New Frame Construction) CEILING JOIST (24” centers shown) 10” ROUND DUCT (OUTLET) ACCESS PANEL Factory-shipped unit installed in new construction. MOUNTING SCREWS ACCESS PANEL SCREW Ventilator factory-shipped in straight-through discharge position. MOUNTING BRACKETS MOUNTING (Existing Frame Construction) Factory-shipped unit installed in existing construction. ACCESS PANEL SCREW 8” X 12” TO 10” ROUND TRANSITIONS 10” ROUND DUCT (O...
Este manual também é adequado para os modelos :Sistemas de ventilação - IN-LINE ILB9 (416.41 kb)