Log:
Assessments - 4, GPA: 3.5 ( )

Instruções de Operação Electrolux, Modelo BVM200

Fabricante : Electrolux
Arquivo Tamanho: 218.78 kb
Arquivo Nome : b2935caa-6816-4334-d993-1173576b8746.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


S Watch out for children, pets, open windows, or freshly washed cars. Blow debris away safely. S Use the full blower nozzle extension so the air stream can work close to the ground. S After using blowers and other equipment, CLEAN UP! Dispose of debris in trash receptacles. FUELING WARNING: Remove fuel cap slowly when refueling. This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality 2-cycle air-cooled engine oil. We recommend Poulan or Poulan Pro brand oil. Mix gasoline and oil at a ratio of 40:1 (A 40:1 ratio is obtained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline). Do not use automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow the instructions printed on the container. Always read and follow safety rules under HANDLE FUEL WITH CAUTION in the safety rules section. IMPORTANT Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. STARTING TO STOP THE ENGINE D To stop the engine, press and hold the ON/ STOP switch in the STOP position until engine comes to a complete stop. BEFORE STARTING THE ENGINE You MUST make sure the tubes are secure before using the unit. D Fuel engine. Move at least 10 feet (3 me ters) away from the fueling site. --5 D Hold the unit in the starting position as shown. Make sure the blower end is directed away from people, animals, glass, and solid objects. BlowerVacuumSTARTINGPOSITION WARNING: When starting engine, hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property, or causing serious injury to bystanders or the operator. STARTING A COLD ENGINE (or warm engine that has run out of fuel) S Move throttle lever to the position. S Move choke lever to FULL CHOKE. S Slowly press the primer bulb 12 times. Throttle Lever Primer Button Choke Lever Switch S Pull starter rope sharply until engine attempts to run, but no more than 5 pulls (below 30_ F, 8 pulls). NOTE: If engine attempts to start before the 5th pull, go to next step immediately. S Move the choke lever to HALF CHOKE. S Pull the starter rope sharply until the engine runs, but no more than 5 pulls (below 30_ F, 10 pulls). Run engine for 5 seconds, then move choke lever to OFF CHOKE. S Allow the unit to run for 30 more seconds at OFF CHOKE before moving the throttle lever to position. If engine has not started after 5 pulls (at HALF CHOKE), repeat STARTING A COLD ENGINE procedure. If engine still does not start, proceed to STARTING A FLOODED ENGINE. STARTING A WARM ENGINE S Move throttle lever to the position. S Pull starter rope sharply until engine runs, but no more than 5 pulls. NOTE: If engine has not started, pull starter rope 5 more pulls. If engine still does not run, it is probably flooded. - -- -- 6 -- DIFFICULT STARTING (or starting a flooded engine) S Move the choke lever to OFF CHOKE. S Move throttle lever to the position. S Pull rope to clear engine of excess fuel. This could require pulling the starter rope many times. If unit still doesn’t start, call 1-800-554-6723. SERVICE We recommend all service and adjustments not listed in this manual be performed by an authorized service dealer. CARBURETOR ADJUSTMENTS Your carburetor is equipped with limiter caps. Carburetor adjustment is a complicated task. We recommend that you take your unit to an authorized service dealer. Damagemay occur if you turn the needles beyond the limiter stops. IGNITION TIMING Ignition timing is fixed, non-adjustable. SPARK PLUG Replace the spark plug yearly using a Champion RCJ--6Y plug. Spark plug gap is 0.025”. CHECK MUFFLER BOLTS WARNING: Avoid touching muffler unless engine is cold. A hotmuffler can cause serious burns. Once each year, ensure muffler bolts are secure and tightened properly to prevent damage. Remove muffler cover and tighten the two muffler bolts (100 in/lbs). Replace muffler cover when finished. TROUBLE CAUSE REMEDY Engine will not start. S Engine flooded. S Fuel tank empty. S Spark plug not firing. S Fuel not reaching carburetor. S Compression low. S See “Starting Instructions.” S Fill tank with correct fuel mixture. S Install new spark plug. S Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace. S Contact authorized service dealer. Engine will not idle properly. S Carburetor requires adjustment. S Crankshaft seals worn. S Compress...


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias