Assessments - 3, GPA: 3.7
(
)
)
|
Fotos e especificações Billy Goat CR550HC |
Facilidade de uso
Tests were performed on 5-25-2006 under the conditions listed below. General Conditions: Sunny Temperature: 72.32oF(22.4oC) Wind Speed: 3.8 mph (6.12kph) Wind Direction: East Humidity: 62.2% Barometric Pressure: 29.9Hg (101.3kpa) INTENDED USE INTENDED USE: This machine is designed for removing thatch from your lawn, renovation of existing lawns, and to assist in overseeding operations. The machine should not be used for any other purpose than that stated above. Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for damaged or worn reel, loose pulley bolts or set screws, loose engine or lodged foreign objects. (See trouble shooting section on page 12). Part No 350245 Form No F062206A 6 CR Owner’s Manual INSTRUCTIONLABELSThelabelsshownbelowwereinstalledonyourBILLYGOAT®CRPowerRake.Ifanylabelsaredamagedormissing,replacethembeforeoperatingthisequipment.ItemnumbersfromtheIllustratedPartsListandpartnumbersareprovidedforconvenienceinorderingreplacementlabels.ThecorrectpositionforeachlabelmaybedeterminedbyreferringtotheFigureandItemnumbersshown. LABELDANGERKEEPHANDSLABELCLUTCHITEM#49DANGERFLYINGDEBRISANDFEETAWAYP/N830503ITEM#48P/N810736ITEM#51P/N400424LABELCAUTIONGUARDLABELEXPLOSIVEFUELLABELINSTRUCTIONHEIGHTADJ. ITEM#52P/N900327ITEM#50P/N400268ITEM#35P/N350224ENGINELABELS/CONTROLSHONDA Part No 350245 Form No F062206A 7 Part No 350245 8 Form No F062206A CR Owner’s Manual PACKING CHECKLIST Your Billy Goat Power Rake is shipped from the factory in one carton, completely assembled. PUT OIL IN ENGINE BEFORE STARTING ASSEMBLY READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box the Handle Assembly is attached and folded over 1. ASSEMBLE the left rear wheel to the axle using .” wrench. 2. UNFOLD the upper handle (item 26) and slide handle lock loops (item 28) into place to secure the upper handle to the lower. 3. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Move height adjust lever to down position, to level engine during checking. See engine manufacturers instruction manual. 4. CONNECT spark plug wire. Boxing Parts Checklist Honda GC 5.0 OHC Literature Assy P/N-350243 PARTS BAG & LITERATURE ASSY Warranty card P/N- 400972, Owner’s Manual P/N-350245, Declaration of Conformity P/N-350139, and Literature CR Accessories 350246. 28 28 26 Part No 350245 9 Form No F062206A CR Owner’s Manual OPERATION Like all mechanical tools, reasonable care must be used when operating machine. Inspect machine work area and machine before operating. Make sure that all operators of this equipment are trained in general machine use and safety. PUT OIL IN ENGINE BEFORE STARTING STARTING ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. Engine must be level when checking and filling oil and gasoline. FUEL VALVE: Move fuel valve to "ON" position (when provided on engine). STOP SWITCH: Located on the engine. "slow/stop" position. CHOKE: Operated with choke lever on side of engine. THROTTLE: Controlled by throttle lever on the motor. IF YOUR UNIT FAILS TO START: See Troubleshooting on page 12. HANDLING & TRANSPORTING: This unit requires two people to lift it. With the handle in the folded position, lift holding the lower handle and belt/shaft guard one on each side of the machine. Secure the machine in place during transport. See page 3 for weight specifications Never lift the machine while the engine is running. ADJUSTING BLADE DEPTH The depth of the blades can be raised or lowered by rotating the knob on the top of the adjustment lever. The blades are lowered by rotating the knob counter-clockwise, and raised by rotating the knob clockwise. The relative depth of the blades can be gauged by using the depth scale located on the right front corner of the engine base. FOLDING HANDLE This unit is equipped with a folding upper handle for easier storage and transportation. The handle can be folded by sliding the handle lock loops (item 28) up. This releases the upper handle, allowing it to be folded over the unit. BLADE POSITION & DEPTH CONTROL LEVER The blades can be raised or lowered into the ground by height adjustment lever on the engine base. The resulting blade depth can be adjusted higher or lower. See ADJUSTING BLADE DEPTH. CR Owner’s Manual RAKING OPERATION MOW: Mow the lawn to it's normal cut height DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass. SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface (i.e. driveway, or sidewalk). START ENGINE: See page 9. ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the turf. RAKE: Rake a small test ar...