Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
Always follow mix ratio found on stabilizer container. Run engine at least 10 min. after adding stabilizer to allow it to reach the carburetor. 16.5 HANDLING & TRANSPORTING: STORAGE 16.4 Be sure engine has come to a complete stop before removing or emptying bag!! This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings page 2-3). Many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas. However, following these rules will help maintain your machine's ability to vacuum in dusty conditions: •Run machine at idle to quarter throttle. •Machine or pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before use. Having one or more spare Felt Filter (890435) is a good way to reduce down time while dirty bags are being cleaned. IF YOUR UNIT FAILS TO START: See Troubleshooting on page 8. Vacuumed leaves, grass and other organic material from your own yard can be emptied into a pile or composter to provide enriched soil for later use as fertilizer in gardens and flower beds Note: Allow green chips to dry before spreading around living plants. 16.10 COMPOST Hint! SPARK PLUG THROTTLE STOP BAG PRESENCE SWITCH NOTE: Outer bag and rod (items 1 and 3) MUST depress the bag presence switch (item 17) for the unit to start. See fig.1 fig 1. INTENDED USE: This machine is designed for vacuuming leaves, grass clippings and other types of organic litter as well as debris mixed with cans, bottles and small amounts of sand; however, vacuuming cans, bottles and sand will affect the longevity of your machine. Inspect machine work area and machine before operating. Make sure that all operators of this equipment are trained in general machine use and safety. Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects. Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 7). Like all mechanical tools, reasonable care must be used when operating machine. Part No. 890049 Form No. F100202A PARTS DRAWING Page 6 of 8 18 SV50HR Part No. 890049 P a g e 7 o f 8 Form No. F100202A 19 * Denotes standard hardware item that may be purchased locally. Item PARTS SV50HR QTY No. LIST Part No. 1 OUTER DEBRIS BAG 890351 1 2 THROTTLE CONTROL 850270 1 3 ROD BAG NO CHANNEL 890036 1 4 NUT LOCK (1/4 - 20 ) *8160001 17 5 SCREW CAP ( 1/4 - 20 x 1-1/2 HEX ) *8041008 2 6 HANDLE UPPER W/GRIP 890439 1 7 AXLE HEIGHT ADJUST 890389 1 8 SCREW CAP 5/16 - 18 x 1-3/4 *8041031 2 9 CLAMP CABLE 1" I.D. 900813 2 10 TY WRAP *900407 2 11 BAG BAG SUPPORT 900039 1 12 LATCH BAG 890356 1 13 PLATE BAG NO CHANNEL 890039 1 14 BRACKET HANDLE SV 890532 2 15 BOLT CARR. 5/16 - 18 x 3/4 ZP 8024039 2 16 WASHER FLAT 1/2 SAE *8172011 4 17 SWITCH PLUNGER 890440 1 18 BRACKET - LOWER HEIGHT ADJUSTMENT 890021 1 19 SCREW 3/8 X 1 1/2 TAPTITE 890408 4 20 SPRING-COMPRESSION 900136 1 21 TIRE - ONLY (PER ASSY) 900507 1 22 PIN - HAIR COTTER 900471 1 23 CABLE HEIGHT ADJUSTMENT 890019 1 24 BOLT - CARRIAGE 5/16 - 18 x 4 1/2 *8024054 4 25 GRIP HANDLE 400570 2 26 NUT LOCK 5/16 - 18 HEX *8160002 6 27 HANDLE LOWER 890346 1 28 PLATE HANDLE SUPPORT 900933 1 29 ENGINE PLATE MOUNT 890337 1 30 WASHER FLAT CUT 5/16 *8171003 2 31 SCREW CARRAIGE 1/4-20 x 3/4 *8024021 12 32 SCREW CAP 1/4 - 20 x 1/2 HWH 890359 6 33 STRAIN RELIEF HAYCO 1244 500282 1 34 WHEEL ASS’Y (incl. items 21) 900509 4 35 WASHER 0.75 “C” 900997 1 - 0 36 PLATE DEFLECTOR SV 890011 1 37 HEIGHT ADJUST ASSY (incl. items 18,20,22,23,25) 890013 1 38 SEAL BAG 890018 2 39 1/2-13 CAP NUT NP W/PATCH 890530 4 40 SCREW CAP 1/4 - 20 x 1 - 1/4 *8041007 4 41 HARNESS ASSY 890442 1 42 SCREW SELF TAPPING 10 - 24 x 1/2 *8123086 1 43 NOZZLE MAINFRAME ASS’Y (incl. one of items 29,44,42) 890391 1 44 PLUG HOUSING 900146 1 45 SCREW CAP 1/4-20x 1-3/4 *8041009 2 46 SCREW SM 1/4 x 3/4 TYPE A *8122082 4 47 PLATE SKID (incl. items 78) 890413 1 48 IMPELLER ASS’Y (incl. items 49, 50, 51) 890382 1 49 KEY 900162 2 50 WASHER LOCK 3/8 TWISTED TOOTH 400502 1 51 SCREW CAP 3/8 -24 x 1 (HARDENED)(TORQ.50 FT-LBS)(68N.m) 900154 1 52 HOUSING ASS’Y (incl. items 29, 62, 84, 86) 890388 1 53 ENGINE HONDA 5.5 H.P. GXV160 KN12 900615 1 54 TERMINAL PIGGYBACK 3/16 890010 1 55 LABEL DO NOT FILL WHEN ENGINE IS HOT 400268 1 56 LABEL EAR EYE BREATHING 890254 1 57 LABEL DANGER FLYING DEBRIS 810736 1 58 LABEL READ OWNER'S MANUAL 890301 1 59 LABEL DANGER CUT FINGER 400424 2 60 PLATE UPPER HEIGHT ADJUST 890005 1 Part No. 890049 Page 8 of 8 Form No. F100202A 20 Before Requesting Service Review These Suggestions Engine Service and Warranty Contact your nearest engine manufacturer's authorized servicing dealer. 22.1 22 BILLY GOAT INDUSTRIES INC. 1803 S.W. JEFFERSON LEE'S SUMMIT, MO 64082 / USA PHONE: 816-524-9666 FAX: 816-524-6983 WARRANT...