Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
Space Requirements The diagram below is provided as a representation only of the space envelope required for installation of Xerox equipment. Diagram is a representation only and not drawn to scale. WIDTH DocuTech 61xx Representation only. DEPTH Note: The 6100, 6115, 6135 are available with and without a stand to support the controller. If a stand is ordered, it will be positioned to the left of the printer, within the service space envelope. If no stand is ordered, the controller will be placed on the floor to the left of the printer in the service space envelope. Note: The dimensions shown below provide the overall service space required, including the space to the nearest obstruction. The dimensions are in inches and are absolute minimums. With stand Without stand Configuration Width Depth Width Depth 6100, 6115, 6135 with interposer, and Finisher 243.0" 114.0” 240.0” 114.0" 6100, 6115, 6135 without Interposer, with Finisher 196.0" 114.0” 193.0” 114.0" Electrical Requirements Printer/Finisher/Binder Line Options: Single Source Voltage 208/240 Amperage 50 Cycles 60 Hz Receptacle Xerox Part No. 600S3779 Receptacle NEMA Part No. 14-50R Power Cord Xerox Part No. 98K19950 117K9940 Receptacle Diagram Please ensure electrical, space, and supplies are available prior to equipment delivery. * Dedicated power outlets required. Ensure each power cord has a separate circuit that cannot be shared with other devices. *15 ft. power cord(s) are provided, however, the distance from the equipment to the outlet should not exceed 13.1 ft. Electrical Requirements Digital Front End (DFE) Controller Platform: Line Options: Dedicated Voltage 110V Amperage 15 Cycles 60 Hz 15 amp Receptacle Xerox Part No. 20 amp Receptacle Xerox Part No. 600S3704 600S3703 Receptacle NEMA Part No. 5 - 20R or 5 - 15R Receptacle Diagram or • All controller configurations require a 110VAC, 15 Amp grounded receptacle for the outlet strip that provides receptacles for the controller and its peripheral devices (monitor, modem, CDROM drive, and tape drive) • Adapters that eliminate the ground connection to the outlet can not be used. • Xerox provides 15 feet of cabling with Teflon coating (Plenum rated), to connect the controller to the Processor/Finisher. Interposer Line Options: Dedicated Voltage 120 Amperage 15 Cycles 60 Hz Receptacle Xerox Part No. 600S3704 Receptacle NEMA Part No. 5 - 15R Power Cord Length 6 feet Receptacle Diagram Installation Considerations • There should be a minimum of 78 inches (1,981mm) clearance from the floor to the nearest overhead obstruction. • Mobility Assist Device - The optional mobility assist device reduces the installation clearance required to 30 inches (760mm) at the processor end of the printer and 15 inches (380 mm) at the finisher end. • For proper operation, the printer must be perfectly level. The floor must be level within 2 degrees in any direction. On floors less than 2 degrees out of level, installation personnel install a leveling kit to level the machine. • If the floor is more than 2 degrees out of level, this condition cannot be corrected by the leveling kit. Another suitable location must be found for the printer to be installed properly. • A minimum 50-inch clearance of exclusive operator area must be maintained in front of each component. This space cannot be shared. • A minimum of 36 inches of clearance is required in the back of each component for general service clearance. Please ensure electrical, space, and supplies are available prior to equipment delivery. Physical requirements • The DocuSP Controller M...
Este manual também é adequado para os modelos :Scanner / Copiadora / MFP - 6135 (43.82 kb)