Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
No more inconvenience from cables or headphone wires! To ensure you get the best performance from your FM wireless stereo surround sound system please read this manual carefully. IMPORTANT Read these instructions.All the safety and operating instructions should be read before using the wireless headphone system. Check if the voltage indicated on the type plate of the adapter corresponds to the local mains voltage before connecting to the mains power supply. Remove the batteries from the headphone’s battery compartment and disconnect the adapter from the mains if the system is not in use for a long period. Prevent fire or shock hazard: do not expose this equipment to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight. Radio equipment for wireless audio applications is not protected against disturbance from other radio services. IMPORTANT Before using the FM headphone for the first time, please ensure that the batteries are fully charged for about 16 hours.This will guarantee a longer operating lifetime of the batteries. Benefits of Philips latest RF/FM wireless technology Wireless transmission The FM transmitter transmits the stereo audio signal from your audio or video source to your FM headphone without wires. Wide transmission range Your FM headphone can receive signals up to 100 meters away. High-frequency radio system The FM headphone set uses a high radio frequency as the signal carrier, ensuring a very clear, sharp reception. Surround Sound The FM headphone features SRS headphone™ to enjoy full surround experience without disturbing others. Extended Frequency response The FM headphone set incorporates improved technology to achieve a frequency response up to 24 kHz enabling the finest musical details to be transmitted. Mute function Reduces the noise disturbance when the sound signal is too low or not available. 4 XP SBC HC 8900/00-1.1 16-08-2001 15:30 Pagina 5 General information Automatic power on/off indicator The FM transmitter automatically switches on and starts transmitting when audio signals are detected at the audio input (red LED).When no audio signals are detected the FM transmitter automatically switches off after a few minutes. Automatic tuning The FM headphone automatically tunes to the right transmission frequency if you push the tuning button. Automatic rechargeable system The FM transmitter automatically recharges the headphone’s built-in rechargeable LR03/AAA NiMH batteries. Just position the headphone on the transmitter and contact.The green LED on the transmitter and the blue LED on the headphone’s headband both light up during charging. Easy transmission The FM headphone is able to receive signals from the transmitter, even through barriers such as doors, walls and windows. Multiple headphones with one transmitter An additional number of headphones and/or wireless speakers can be used with a single transmitter if they: - operate in the 864 MHz band -can detect a 25 kHz pilot tone - apply identical companding parameters. Please consult the appliance’s electrical specification sheets for confirmation on compatibility. Kit contents This FM headphone system consists of the following accessories: 1 x SBC HC8902 FM transmitter 1 x SBC HC8905 FM headphone 1 x SBC CS030/00 12Volt / 200mA adapter (for UK version: SBC CS030/05) 2 x rechargeable batteries LR03/AAA (NiMH), 550 mAh 1 x 3.5 mm stereo plug to 2x RCA audio cable (2 m) 1 x 3.5 mm stereo plug to 2x RCA connector cable (20 cm) 1 x 3.5 mm plug to 6.3 mm stereo adapter plug English 5 XP SBC HC 8900/00-1.1 16-08-2001 15:30 Pagina 6 Controls English Transmitter (figure 1) 1 Power indicator – lights up when audio signals are detected at the audio input. – starts blinking if the audio signals at the input are too strong: set the input selector switch to 3 V or reduce the audio volume of the audio source. 2 Recharging indicator – lights up when headphone is replaced on the FM transmitter. Completely flat batteries will be fully charged after about 16 hours. 3 Recharging contact – make sure you align your headphone to this contact for recharging. 4 DC power – connect to the 12 Volt/200 mA AC/DC adapter 5 3.5 mm stereo headphone audio input – connects your FM transmitter to an audio source 6 Input selector switch – select 250 mV input if connected to a line output of an audio source – select 3 V input if connected to a headphone output of an audio source 7 Channel switch – select one of 7 channels for best reception.We advise you to select channel 1 as a first option. 8 Controls plate Headphone (figure 2) 9 Power indication – lights up when in use. When batteries are low, the power indicator flashes, and you should recharge the headphone for about 16 hours before the next use. 10 Power On/Off – push the button to switch the headphone on/off. 11 SRS™ indication – lights up when the SRS™ surround sound mode is activated. 12 SRS™ On/Off – push the button to switch the SRS™ surround sound mode on/off. 13 Rechar...