Your new hearing instruments will be your constant companions from now on. With these technically perfected hearing instruments you profit from our many years research and experience in microelectronics. Soon it will be easy for you to hear again. Good hearing is an important requirement for your physical well being. With your new hearing instruments, which will accompany you daily, you will again enjoy taking an active part in the world of speech and music. And as with any constant companion, y

This naturally requires some care in their handling. They should then always give you good service. All Caution! As with all electrical, non gas-encapsulated instruments, the hearing instruments must not be operated in explosion-endangered rooms. 29 How to solve failures yourself In selecting your PRISMA 2 hearing instruments you have chosen extremely dependable devices. However, should a fault occur, it can usually be corrected quickly. Important tips: If the instrument whistles Test the instru

Battery changing ЎЎ Ў Ў Open the battery compartment Insert the battery Close the battery 2/2 P compartment When inserting the battery please pay attention to the plus side on the battery. The plus (+) side of the battery is always the smooth side.You can recognise the minus (–) side by the coloured ring. You should always keep spare batteries at hand. If you feel you cannot change the battery yourself, ask someone to help you: a family member, friend or your hearing instrument specialist. 7 Saf

1) Printed in U.S.A. english PUSH TO HEAR (PTH) INSTRUCTION O Set PTH and audio device volumes to lowest levels. © Connect earphones and audio device. © Switch PTH ON. Power LED light should be green. When LED turns red, battery is low and should be replaced. © Slowly raise the PTH volume to a comfortable level. Tapping the microphone should not cause discomfort. © Switch PTH OFF. Adjust volume on your audio device. NOTE: The Push-to-Hear module has a built-in limiter to minimize sudden

GENERAL ---------------------------------------- File Options: Compatibility: PDF 1.3 Optimize For Fast Web View: No Embed Thumbnails: No Auto-Rotate Pages: Collectively By File Distill From Page: 1 Distill To Page: All Pages Binding: Left Resolution: [ 600 600 ] dpi Paper Size: [ 595 842 ] Point COMPRESSION ---------------------------------------- Color Images: Downsampling: Yes Downsample Type: Bicubic Downsampling Downsample Resolution: 144 dpi Downsampling For Images Above: 200 dpi Compressi

It should contribute to deepening your friendship with your new partners in the matter of better hearing. We want to help you to handle your hearing instruments correctly, so that they will become an important part of your life. Wishing you much success, Your Siemens Team The best new hearing In this brief guide you will find instructions for inserting, placing and adjusting your hearing instruments. There are also tips and information on correct handling, cleaning, care and battery changing. An

In this guide, you’ll find instructions about insertion, removal and use of your CENTRATM hearing system. There are also tips and information on proper handling, cleaning, care and changing of the batteries. In addition, a troubleshooting section is offered for your reference. Your hearing improvement with a hearing system depends on the fit of the hearing instruments, the type and degree of hearing loss, and proper diagnostic testing. Of course, a hearing system cannot restore normal hearing, a

Small recess in the Nib in the audio shoe hearing system housing Expect the CIELO Dir audio shoe 16 Before the audio shoe can be connected to the hearing system the following steps have to be fullfilled: 1. Open the battery compartment 2. Open the audioshoe cover 3. Close the battery compartment Attaching the audio shoe Take the audio shoe and hook the two nibs into the two small recesses of the hearing system housing. Slide the audio shoe to the inner side of the hearing system housing until it

All rights reserved Oct. 23, 2006 Contents Chapter 1: Introduction & Setup 1.1 History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 Basic Test Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.3 Options . . . . . . .

Press F2 to choose the type of aid you are testing. The selections are AGC 50, LINEAR 50, LINEAR 60. • Choose LINEAR 60 for most linear aids. • Choose LINEAR 50 for high-gain aids. • Choose AGC for AGC aids. Note: If you are testing a digital aid, you should usually select AGC for this setting. However, ask the hearing aid manufacturer for guidance. 2. Press F3 to select the last frequency of the three frequency average used in the test sequence. See Section 2.4.1 for details. 3. Press F5 to tur