Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end. 2. Hook end of spring into control arm with loop opening up as shown. (See Fig. 5) 3. With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring. ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotator head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower. 2. Position chute rotator head over chute bracket. If nec es sary, rotate chute assembly to align square and pin on under side of chute rotator head with holes in chute brack et. 3. With chute rotator head and chute bracket aligned, po si tion chute rotator head on pin and threaded stud of mounting bracket. 4. Install 3/8 washer and locknut on threaded stud and tighten securely. CHUTE ROTATOR HEAD 3/8 WASHER 3/8 LOCKNUT THREADED STUD PIN ROTATOR HEAD MOUNT ING BRACKET CHUTE BRACKET Fig. 7 ALIGN BEFORE TIGHTENING LOCKNUT INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with 5/16-18 carriage bolt and 5/16-18 locknut as shown. Tighten securely. 2. Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt and 1/4-20 locknut as shown. Tighten nut securely. Eyelet will be loose on shoulder bolt. 3. Install spring hooks between hex nuts on chute rotator head and into hole in chute deflector as shown. Fig. 8 HOOK BE TWEEN HEX NUTS ON CHUTE ROTATER HEAD SPRING CHUTE DE FLEC TOR 5/16-18 CARRIAGE BOLT 5/16-18 LOCKNUT REMOTE CABLE BRACKET 1/4-20 LOCK NUT CABLE EYELET 1/4-20 SHOULDER BOLT CHUTE DEFLECTOR CONTROL LEVER FIG. 9 CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the factory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI. 7 OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT. FORWARD REVERSE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. IGNITION KEY. INSERT TO START AND RUN, PULL OUT TO STOP. DISENGAGED ENGAGED SNOW TRACTION DISCHARGE DRIVE CONTROL 8 9 MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. Drive speed control lever - used to select forward or reverse motion and speed of snow thrower. Traction drive control lever - used to engage power-propelled for ward or reverse motion of snow thrower. Auger control lever - used to engage auger motion (throw snow). Discharge chute control lever - used to change the direc tion the snow is thrown. Deflector remote control lever - used to change the dis tance the snow is thrown. Skid plate - used to adjust height of scraper bar from the ground. Drift cutter - used to cut through deep snowdrifts. Toolbox - used to store spare shear bolts, locknuts and wrench. Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use. Electric start button - used for starting the engine. Recoil (auxiliary) starter handle - used for start ing en gine. Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine. Choke Control - used for starting a cold engine. Throttle/engine control - used to se lect either FAST or SLOW engine speed and to STOP the engine. LH and RH turn triggers - used to steer the snow thrower. DEFLECTOR REMOTE CONTROL LEVER TRACTION DRIVE CONTROL LEVER DISCHARGE CHUTE CONTROL LEVER DRIVE SPEED CON TROL LEVER AUGER CONTROL LEVER MUF FLER TOOLBOX HANDLE KNOB SKID PLATE CHUTE DE FLEC TOR DISCHARGE CHUTE AU GERS NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT. LIGHT LH TURN TRIGGER DRIFT CUTTER CLEAN-OUT TOOL RECOIL (AUXILIARY) STARTER HANDLE THROTTLE / ENGINE CONTROL MUF FLER GAS O LINE FILLER CAP SAFETY IGNITION KEY CHOKE CONTROL ELECTRIC START BUTTON PRIM ER FUEL SHUT-OFF VALVE Fig. 10 OPERATION OPERATION The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad justments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR SNOW...