Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
3. After adjustment, retighten the ten- sion bolt lock nuts. TENSION BOLT 8. 8. I / i- i Before storing the snowblower for an extended period: 1. Be sure the storage area is free of excessive humidity and dust. 2. Drain the fuel - m Gasoline is extremely flammable and explosive under certain conditions. Do not smoke or allow flames or sparks in the area. FUEL ‘VALVE a. Drain the fuel. CARBURETOR DRAIN SCREW b. Loosen the carburetor drain screw, and drain the gasoline into a suitable container. Retighten the drain screw after all gasoline has been drained. Remove the spark plug and pour three tablespoonsful of clean motor oil into the cylinder. Pull the starter rope slowly two or three times to distribute the oil. Reinstall the spark plug. Remove the spark plug and pour three tablespoonsful of clean motor oil into the cylinder. Pull the starter rope slowly two or three times to distribute the oil. Reinstall the spark plug. Apply oil to the following parts for lubrication and rust prevention. Apply oil to the following parts for lubrication and rust prevention. I -m AUGER CLUTCH LEVER PIVOT l• FRICTION DISK SHAFT 1. With the fuel tank drained, turn the chute forward and stand the snow thrower on end as shown. BOTTOM COVER 2. Remove the bottom cover. FRICTION DISK SHAFT 3. Oil the friction disk shaft. Never oil the friction disk and dl disk. 4. Install the bottom cover. -.. -.. . TROUBLESHOOTING ---1 1 When the engine will not start :] 1. Is there enough fuel? 2. Is the fuel valve on? 3. Is gasoline reaching the carburetor? To check, loosen the drain screw with the fuel valve on. bw If any fuel is spilled, make sure the area is dry before testing the spark plug or starting the engine. Fuel vapor or spilled fuel may ignite. 4. Is the engine switch on? 5. Is there a spark at the spark plug? a. Remove the spark plug cap. Clean any dirt from around the spark plug base, then remove the spark plug. b. Install the spark plug in the plug cap. c. Turn the engine switch on. d. Grounding the side electrode to any engine ground, crank the engine to see if sparks jump across the gap. e. If there are no sparks, replace the plug. If OK, try to start the engine according to the instructions. 6. If the engine still does not start, take the snowblower to the dealer. IWhen the auger or blower will not operate: ~- Check the shear bolts and replace if broken off. Secure the shear bolts with 6 mm nuts. Three spare shear bolts are supplied with the HS50 snowblower. SHEAR BOLTS r r SPECIFICATIONS Engine Model: HONDA engine G200 Maximum output: 5.0 HP/l,800 r.p.m. (Cam shaft P.T.O.) Displacement: 197 cm3 (12.1 cu.in) Bore x stroke: 67 x 56 cm (2.64 x 22.0 in) Starting method: Manual (Recoil starter) Ignition system: Flywheel magneto type Oil capacity: 0.7 liter (0.74 US qt, 0.62 Imp qt) Fuel tank capacity: 3.5 liter (0.92 US gal, 0.77 Imp gal) ~ Spark plug: BR4HS (NGK), Wl4FR-U (ND) Frame 11. 11. Owner Satisfaction Your satisfaction and goodwill are important to your dealer and to us. Normally, any problems with the product will be handled by your deal- er’s service department. Sometimes, however, despite the best inten- tions of all concerned, misunderstandings can occur. If your problem has not been handled to your satisfaction, we suggest you take the fol- lowing action: l• Discuss your problem with a member of dealership management. Of- ten complaints can be quickly resolved at that level. If the problem has already been reviewed with the Service Manager, contact the owner of the dealership or the General Manager. l• If your problem still has not been resolved to your satisfaction, con- tact the Motorcycle and Power Products Customer Relations Depart- ment at the regional office of American Honda Motor Co., Inc. in your area. Regional office locations are shown on the following page. We will need the following information in order to assist you: -Your name, address, and telephone number -Product model and serial number -Date of purchase -Dealer name and address -Nature of the problem After reviewing all the facts involved, you will be advised of what action can be taken. Please bear in mind that your problem will likely be re- solved at the dealership, using the dealer’s facilities, equipment, and personnel, so it is very important that your initial contact be with the dealer. Your purchase of a Honda product is greatly appreciated by both the dealer and American Honda Motor Co., Inc. We want to assist you in ev- ery way possible to assure your complete satisfaction with your purchase. Current customer service contact information: Current customer service contact information: Honda Power Equipment dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership's management. The Service Manager or General Manager can help. Almost all problems are solved in this way. If you a...