Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
2. Put the chute crank rod through the bracket on the lower handlebar. (See Figure 3) 3. Install the chute crank rod onto the shaft. 4. Fasten the chute crank rod with the screw and nut that were removed in step 1. Figure 2 Shaft Chute Crank Rod Nut Screw 1740274 10 ASSEMBLY 1740274 11 HOW TO ASSEMBLE THE HANDLE 1. Remove the packing material from the upper and lower handles. 2. Loosen the knobs on each side of the handle. (See Figure 3) 3. Raise the upper handle to the operating position (see Figure 4). Hold the upper handle apart to prevent scratching the lower handle. NOTE: Make sure the cables are not caught between the upper and lower handle. 4. Tighten the knobs. Upper Handle Knob Figure 3 Lower Handle Chute Crank Rod Upper Handle Knob Figure 4 Lower Handle HOW TO INSTALL THE CHUTE 1. Remove the three bolts and lock nuts from the chute base (see Figure 5). 2. Install the chute with the bolts and locknuts. Make sure the locknuts are to the outside as shown. Tighten securely. Figure 5 Locknuts Chute Chute Figure 6 ASSEMBLY CHECKLIST Before you operate your new snowthrower, to ensure that you receive the best performance and satisfaction from this quality product, please review the following checklist: . All assembly instructions have been completed. . The discharge chute rotates freely. . No remaining loose parts in carton. While learning how to use your snow thrower, pay extra attention to the following important items: . Make sure the fuel tank is filled with the correct mixture (50:1 ratio) of gasoline and Husqvarna 2 Cycle oil. . Become familiar with the location of all controls and understand their function. . Before starting the engine, make sure all controls operate correctly. 1740274 12 OPERATION 1740274 13 KNOW YOUR SNOWTHROWER READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOWTHROWER. Compare the illustrations with your SNOWTHROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Figure 7 Recoil Starter Handle Auger Drive Lever Chute Control Rod Discharge Chute Chute Deflector Primer Button Recoil Starter Ignition Switch Key Choke Control Auger ENGINE AND SNOW THROWER OPERATING CONTROLS The engine operating controls and their functions are as follows: Auger Drive Lever . Starts and stops the auger. Chute Control Rod . Changes the direction of snow throwing through the discharge chute. Chute Deflector . Changes the distance the snow is thrown. Discharge Chute . Changes the direction the snow is thrown. Ignition Switch Key . Must be inserted and turned to the ON position to start the engine. Turn key to the OFF position to stop the engine. Recoil Starter Handle . Starts the engine manually. Electric Starter Button . (Not shown) On electric start models, use to start the engine when using the 120V electric starter. Choke Control . Used to start a cold engine. Primer Button . Injects fuel directly into the carburetor manifold for fast starts in cold weather. OPERATION SNOWTHROWER OPERATION The most effective use of the snowthrower will be established by experience, taking into consideration the terrain, wind conditions and building location which will determine the direction of the discharge chute. NOTE: Do not discharge snow toward a building as hidden objects could be thrown with sufficient force to cause damage. WARNING: Read Owner’s Manual before operating machine. This machine can be dangerous if used carelessly. Never operate the snowthrower without all guards, covers, and shields in place. Never direct discharge toward windows or allow bystanders near machine while engine is running. Stop the engine whenever leaving the operating position. Disconnect spark plug before unclogging the impeller housing or the discharge chute and before making repairs or adjustments. When leaving the machine, remove the ignition key. To reduce the risk of fire, keep the machine clean and free from spilled gas, oil and debris. HOW TO STOP THE SNOWTHROWER 1. To stop throwing snow, release the auger drive lever. (See Figure 9). NOTE: If the snowthrower continues to slowly move forward, see “How To Adjust The Auger Control Cable” in the Maintenance Section. 2. To stop the engine, move the ignition key to the OFF position. HOW TO CONTROL SNOW DISCHARGE 1. Turn the chute control rod to set the direction of the snow throwing. (See Figure 7) 2. Loosen the wing knob on the chute deflector and move the deflector to set the distance. Move the deflector (Up) for more distance, (Down) for less distance. Then tighten the wing knob (See Figure 8). Figure 8 Wing Knob Deflector Down Deflector Up HOW TO THROW SNOW NOTE: If the auger continues to rotate, see “How To Adjust The Auger Control Cable” in the Maintenance 1. Engage the auger drive lever. (See Figure 9). section. 2. To stop throwing snow, release the auger drive lever. HOW TO MOVE FORWARD 1. Hold the auger drive lever against the handle (See Figure 9). The auger will begin rotating. ...
Este manual também é adequado para os modelos :Snow Blowers - 521SSE (994.31 kb)