Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
AugerDrive TractionDrive Spring(Short ,_ Spring(Long) _ I' ' --Figure9 CONNECT REMOTE CHUTE 1. Push remote chute control lever into "Chute Deflector Up" position. 2. Feed "Z" fitting through hole in remote chute bracket. See. 3. Snap remote chute control cable into remote chute bracket. See. 4. Connect "Z" fitting into remote chute control bracket. See. 5. Push remote chute control lever into "Chute Deflector Down" position. 6. Cut tie strap on chute deflector. See Figure. SPEED SELECT LEVER 1. Cut plastic tie securing speed select lever assembly to the shifter bracket. See Figure 10. 2. Remove Iocknut, washer, spring, and the bolt. See Figure 12. 3. Positionspeedselectorlever assembly as shown in Figure 11. 4. Reinstall bolt, spring, washer and Iocknut See Figure 12. 5. Tighten Iocknut until 1/8 to 3/16 inch of the bolt threads protrude pas the Iocknut. 6. Thread the 3/8-16" hex jam nut onto the lever until the nut reaches the end of the thread. See Figure 12. 7. Thread the plastic knob as far as possible and ensure that the knob points forward. 8. Tighten the 3/8-16" hexjam nut against the knob securely. 9. Move shifter through all speeds to ensure proper tension of the spring. If shifter lever sticks in any of the notches, loosen Iocknut 1/2 turn at a time until shifter lever moves more freely. 10. If adjustment of speed of snow blower is needed, refer to "Friction Wheel Adjustment" in the ADJUSTMENT/ REPAIR section. Shifter Bracket Plastic Tie Figure 10 Control Panel Figure 11 F-OOIO60J 10 f!_.'x_*]=1_I=]Ik'4 3. "Rghten the 3/8-16" hex jam against the knob securely. nut 3/jSa-16 Hex m Nut Remote Chute Control Knob Washer Control Locknut Panel • Exposed Thread Figure 12 REMOTE CHUTE CONTROL KNOB 1. Thread the 3/8-16" hex jam nut onto the lever until the nut reaches the end of the thread. See Figure 13. 2, Thread the plastic knob as far as possible and ensure that the knob points forward. HOW TO SET THE SKID HEIGHT Your snow thrower is equipped with height adjust skids on the outside of the auger housing. To adjust the skid height for different conditions, see To Adjust Skid Height paragraph in the Service And Adjustment section. _" CHECKLIST Before you operate your new snow thrower, to ensure that you receive the best performance and satisfaction from this quality product, please review the following checklist: P" All assembly instructions have been Figure 13 HEADLIGHT The headlight on your snow thrower is positioned down for packaging purposes. Rotate upward for operating position. completed. P" The discharge chute rotates freely. _" No remaining loose parts in carton. While learning how to use your snow thrower, pay extra attention to the following important items: _" Engine oil is at proper level. ._" Make sure gas tank is filled properly with clean, fresh, unleaded gasoline. P" Become familiar with all controls- their location and function. Operate controls before starting engine. F-001060J 11 bPj=l--Iri_l[i]_] KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourseff with the location of various controls and adjustments. Save this manual for future reference. Electric Auger. Drive Lever (left hand) Lever StartButton (right hand) , Remote Primer Chute Control Switch ;rank Box Assembly Chute Deflector Discharge Chok_ Control Recoil Throttle Starter Control Handle Figure 14 Auger Drive Lever -Starts and stops the auger and impeller (snow gathering and throwing) Traction Drive Lever -Propels the snow thrower forward and in reverse. Speed Shifter Lever -Selects the speed of the snow thrower (6 speeds forward and 2 speeds reverse). Crank Assembly -Changesthe direction of snow throwingthroughthe discharge chute. Chute Deflector -Changes the distance the snow is thrown. Discharge Chute -Changes the height anddirectionthe snowis thrown. Height Adjust Skid -Adjusts the ground clearance of the auger housing. Ignition Key -Must be inserted to start the engine. Recoil Starter Handle -Starts the engine manually. F-OO1060J Choke Control -Used to start a cold engine. Primer Button -Injectsfuel directlyintothe carburetor manifold for fast starts in cold weather. Remote Chute Control Lever -Push forward to discharge snow high and far. Pull remote lever back to discharge snow down. Throttle Control -Controls the engine speed. Electric Start Button -(If so equipped) Usedto startthe engineusingthe 120V Edectnc starter. Shear Pin -Shear pins are designed to break (to protect the machine) if an obiect becomes lodged in the auger hous- Ing. Toolbox -spare shear pins and spacers are located in toolbox, 12 The operation of any snow thrower can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating the snow thrower. We recommend standard safety glasses or a wide vision safety mask for over your glasses. Manual before ...