Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
However, we reserve the right to change, alter or otherwise improve the product and this document at any time without prior notice. Read the Operator’s Manual • Locate the operator’s manual in the manual packet. Always read and follow the instructions in the operator’s manual. Proper care, performance tips, and safety information are located in this important document. • “Right” and “Left” are from the Operating Position. Raise The Handles • Cut four orange zip ties (E, Figure 3) that secure control cables to handle assembly (C). Be careful not to cut or damage the control cables. • Loosen nuts (B) in upper holes with a 1/2” wrench. Rotate upper handle assembly (A) up. Locate two carriage bolts and two 5/16 nuts in parts bag (B, Figure 1). Slide carriage bolts (D) and nuts (B) into lower holes. Tighten all hardware with a 1/2” wrench or deep socket. Install Chute Rotator Control Handle • Install thin jam nut (B, Figure 4) onto chute rotator rod (C). Install chute rotator control handle (A) onto chute rotator rod (C) turing at least 10 full rotations. • Align chute rotator control handle so it is facing forward and use a 9/16” wrench to tighten jam nut (B) against chute rotator control handle (A). • Slide chute rotator control handle to the right hand side. Install Drift Cutters • Drift cutters (A, Figure 5) are mounted to snowthrower auger housing (C). With a 1/2 wrench remove the hardware (B). Install drift cutters (A) placing tab (D) into square hole (E) and the removed hardware (B). Connecting Shift Rod • Connect shift rod (A, Figure 6) to shift lever (B) secure with lock washer (C) and nut (D) with a 1/2” wrench and a 7/16’ wrench to prevent stud (E) from turning. Chute and Rotator Assembly • Bring chute from pallet to the left side of snowthrower. • Remove special nut (A, Figure 7) and cover (B). • Remove hair pin (C) with a pliers and slide rod (D) forward about 8 inches. • Slide the chute base (A, Figure 8) onto the auger housing (B). • Slide chute support tube (E, Figure 8) on to the carriage bolts (D). Do Not tighten at this time. • Move chute rotator control handle (A, Figure 9) to the right hand side of the machine. • Slide spout rotator rod (B, Figure 9) into hex dash opening (D). It may be necessary to move chute rotator handle (B) for rod to go into dash. • Insert hair pin (C, Figure 9 ) into spout rotator rod (D). • Install cover (B, Figure 7) and secure with special nut (A). • Secure chute support tube (E, Figure 8) to chute base securing with lock nuts (C) using a 9/16 wrench. Quick Setup Guide tems Included: 1 -- Chute Rotator Control Handle 2 -- Ignition Keys 2 -- Cotter Pin 1 -- 3/8” Nut 2 -- 5/16” Lock Nut 1 -- 3/8” Lock Washer 1 -- 3/8” Jam Nut (thin) 3 -- Zip Tie 2 -- Shear Pin 2 -- 3/8” Lock Nut 2 -- Carriage Bolt 1 -- 120V Power Cord 1 -- Operator’s Manual ¦ Operator’s Manual ¦ Chute Rotator Control Handle ¦ One (1) Jam Nut (thin), 3/8”, use 9/16” wrench ¦ One (1) Nut, 3/8”, use 9/16” wrench ¦ One (1) Lock Washer, 3/8” ¦ Two (2) Carriage Bolts, 5/16” x 2-1/4, use 1/2” wrench ¦ Two (2) Lock Nuts, 5/16, use, use 1/2” wrench ¦ Two (2) Lock Nuts, 3/8, use, use 9/16” wrench ¦ 120V Power Cord ¦ Three (3) Zip Ties ¦ Two (2) Keys ¦ Two (2) Extra Shear pins ¦ Two (2) Extra Cotter pins For Assembly You Will Need: • Utility knife • Tin Snips or Banding Cutter • Unleaded fuel • Pliers • Tire Pressure Gauge • 1/2” Combination Wrench or 1/2” Deep Socket & Ratchet • 3/8” Combination Wrench or 3/8” Socket & Ratchet • 9/16” Combination Wrench or 9/16” Socket & Ratchet • 7/16” Combination Wrench Figure 2 Figure 4 Spout Rotator Brake Cable Connection • Slide the spout rotator brake cable (E, Figure 9) between the dash and the handle cross bar as shown. • Slide the rubber dust cover (D, Figure 10) off of plastic fitting (B). • Place “Z” bend of cable (C) into hole (G) of brake lever assembly (E) • Pull plastic fitting (B) behind bracket (E). • Slide chute rotator cable (A) between slot in bracket (E) and push forward to lock in place. • Slide the rubber dust cover (F) over the plastic fitting (B). 2 3 8 Figure 7 TP 1000-4518-01-LW-S Form No. 173xxxx-00 Two-Stage Snowthrower 1694986 10530L, 10.5 Snow...
Este manual também é adequado para os modelos :Snow Blowers - 10530L (2.01 mb)