Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely. INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing rod to lower handle. 2. Insert rod into speed control bracket and secure with retainer spring. SPEED CONTROL ROD HANDLE KNOB LOWER HANDLE PLASTIC TIE UPPER HANDLE FIG. 1 SPEED CON TROL ROD SPEED CONTROL BRACKET RETAINER SPRING SPEED CONTROL LEVER FIG. 2 5 6 ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 2. With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring. TRACTION DRIVE CON TROL ROD DRIVE CONTROL BRACKET RETAINER SPRING TRACTION DRIVE CON TROL LEVER INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod has the long loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown. 2. With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring. TRACTION DRIVE CONTROL ROD PIVOT BRACKET RUBBER SLEEVE LOOP OPEN ING DOWN FIG. 3 FIG. 4 AUGER CONTROL LEVER AUGER CONTROL ROD AUGER CONTROL BRACKET RETAINER SPRING FIG. 6 AUGER CONTROL ROD CONTROL ARM RUBBER SLEEVE LOOP OPENING UP FIG. 5 ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower. 2. Position chute rotater head over chute bracket. If neces sary, rotate chute assembly to align square and pin on un der side of chute rotater head with holes in chute bracket. 3. With chute rotater head and chute bracket aligned, po si tion chute rotater head on pin and threaded stud of mounting bracket. 4. Install 3/8 washer and locknut on threaded stud and tighten securely. CHUTE ROTATER HEAD 3/8 WASHER 3/8 LOCKNUT THREADED STUD PIN ROTATER HEAD MOUNT ING BRACKET CHUTE BRACKET FIG. 7 INSTALL WEIGHT BAG (See Fig. 8) Though seldom required, the weight bag will re duce the ten den cy of the auger housing to ride up on hard, icy drifts. Should conditions require it, install as follows: 1. Shut off engine and wait for all moving parts to stop. 2. Fill weight bag with de sired amount of sand. 3. Place weight bag on top of auger hous ing with mounting clamp at front edge of auger housing as shown. 4. Insert weight bag between the auger hous ing and the bar of the mounting clamp as shown and secure with 5/16-18 x 1-1/2 capscrews. Tight en securely. IMPORTANT: Mount the weight bag in a location which does not cover the warning decals on top of the auger housing. WEIGHT BAG 5/16-18 x 1-1/2 CAPSCREWS BAR AUGER HOUSING MOUNTING CLAMP FIG. 8 CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the factory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI. 7 OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT. FORWARD REVERSE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. IGNITION KEY. INSERT TO START AND RUN, PULL OUT TO STOP. DISENGAGED ENGAGED SNOW TRACTION DISCHARGE DRIVE CONTROL 8 OPERATION DISCHARGE CHUTE CONTROL LEVER RECOIL (AUXILIARY) STARTER HANDLE THROTTLE / ENGINE CONTROL DRIVE SPEED CON TROL LEVER AUGER CONTROL LEVER SKID PLATE CHUTE DE FLEC TOR DISCHARGE CHUTE AUGER GAS O LINE FILLER CAP ENGINE OIL CAP WITH DIPSTICK SPARK PLUG SAFETY IGNITION CHOKE ELECTRIC START BUTTON PRIM ER FUEL SHUT-OFF VALVE NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT. OIL DRAIN PLUG POWER CORD PLUG FIG. 9 KEY CONTROL TRACTION DRIVE CONTROL LEVER HANDLE KNOB MUF FLER TOOLBOX MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. Toolbox - used to store spare shear bolts, locknuts and wrench. Safety ignition key - must be inserted...