Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
AUGER HOUSING GUARD SNOW REMOVAL CONDITIONS RECOMMENDED AUGER HOUSING GROUND CLEARANCE For general use 6-8 mm (0.24-0.31 in) For use on uneven surfaces lo-30 mm (0.39-1.18 in) For use on flat surfaces 0-5 mm (O-0.20 in) NOTE: Track model only -The position of the height adjustment pedal (p. 14) also affects auger housing ground clearance. Set the height adjustment pedal in the middle position (II) before adjusting the skid plates. HEIGHT ADJUSTMENT PEDAL (Track model only) Use the pedal for adjusting the height and angle of the machine in relation to the tracks. 1. Hold the handles and step on the pedal. 2. Raise or lower the machine to the desired position and release the pedal. LOW : Hard snow or fine finish MIDDLE : Normal use HIGH : Deep snow or for transporting the HS50 HEIGHT ADJUSTMENT PEDAL LOW MIDDLE .-HIGH 3. PRE-OPERATION CHECK FUEL LEVEL Inspection: Unscrew the fuel cap. Check the fuel level. Refueling: Use any regular grade automotive gasoline (unleaded gasoline is preferred) with a pump octane rating of 86 or’higher. Never use an oil/gasoline mixture. Prevent dirt, dust or water from entering the fuel tank. CAUTION: Gasoline substitutes are not recommended: they may be harmfull to the fuel system components. FUEL TANK CAPACITY: 3.5 Q (0.92 US gal, 0.77 Imp. gal.) - * Gasoline is extremely flammable and explosive under certain conditions. Refuel in a well ventilated area with the engine stopped. * Do not smoke or allow flames or sparks in the area where the snow thrower is being refueled or where gasoline is stored. * Be careful not to spill fuel when refueling. Fuel vapor or spilled fuel may ignite. Make sure the area is dry of spilled fuel before starting the engine. * DQ not overfill the tank (there should be no fuel in the filler neck). After refuel- ing, make sure the fuel cap is closed securely. * Do not refuel in snow because snow will get into fuel tank and cause engine malfunction. ENGINE OIL LEVEL Inspection: With the snowblower on a level surface, remove the oil filler cap and check the oil level. If the level is low, fill to the top of the oil filler neck with the recommended oil. -20 0 20 40 W’F 1 1 Oil filler neck '-30 -20 -10 o 1ooc OIL CAPACITY: 0.7, P (0.74 US qt, 0.62 Imp. qt) RECOMMENDED OIL: Use high detergent, premium quality motor oil certified to meet or exceed U.S. auto- mobile manufacturers’ requirements for service classification SE or SF (Motor oils classified SE or SF will show this designation on the container.) Select the appropriate oil viscosity for the average temperature in your’ area, as shown in this chart. SAE 5W-30 is recommended for general, all-temperature use. CAUTION. * Engine oil is a major factor affecting engine’ performance and service life. Non- detergent or vegetable oils are not recommended. * Running the engine with insufficient oil can cause serious engine damage. 4. STARTING THE ENGINE 1. Turn the engine switch to the ON position. Engine switch 2. Turn the fuel valve to the ON position. Fuel valve 3. In cold weather and when the engine is cold, turn the choke knob to the CLOSE position. CHOKE’KNOB 4. Pull the starter grip lightly until you feel resistance, then pull briskly. ARTER GRIP NOTE: Don’t allow the rope to snap back; return it gently by hand. Otherwise, the starting mechanism might be damaged. While the engine is in operation, don’t pull the starter grip or damage may result. c 5. Let the engine warm up for several minutes. If the choke has been turned to the CLOSE position, return it gradually to the OPEN position as the engine warms up. I? 5. SNOWBLOWER OPERATION ) 1. Raise the throttle lever (p. 10) to the high position for normal operation. 2. Move the shift lever (p. 10) to select the desired drive speed. DRIVE SPEED WITH LEVER IN THE HIGH POSITION Wheel type Track r 1 ~~~~ 1 tvne 1 _ -. 1 ’ I 1 1 0.32 m/s (1.05 ft/s) 0.21 m/s (0.69 ft/s) 2 0.50 m/s (1.64 ft/s) 0.33 m/s (1.08 ft/s) 3 0.74 m/s (2.43 ft/s) 0.48 m/s (1.57 . ftls), I ! 1 R 1 0.49 m/s (1.6 1 ft/s) 1 0.33 m/s (1.08 h/s) 1 CAUTION: Be sure to set the shift lever into the groove. Do not change direction while the machine is in motion. NOTE: Low speed (1) is recommended for removing deep or hard-packed snow. 3. Track model only -Use the height adjustment pedal (p. 14) to adjust the height and angle of the machine. 4. Adjust the chute direction (p. 12) and chute guide angle (p. 12). 5. Squeeze the auger clutch lever and drive clutch lever (p. 11) to propel the machine and commence snow clearing. High Altitude Operation When operating this snow-blower at high altitude the an-fuel mixture becomes overly rich and engine performance may be reduced and fuel consumption increased. See your authorized HONDA dealer for high altitude adjustment. NOTE: l To move the machine without engaging the snow blowing mechanism, squeeze the drive clutch lever only. Do this when moving the machine to or from the area to be cleared. l To engage the snowblowing mechanism without using the drive m...