Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug. Problem Possible Cause Remedy Engine fails to start. Key is OFF. Push key in to the ON position. Failure to prime cold engine Press primer button twice and restart. Fuel valve is in CLOSED position. Turn valve to OPEN position. Out of fuel. Fill fuel tank. Choke OFF - cold engine. Turn choke to ON, set throttle to FAST. Engine flooded. Turn choke to OFF; try starting. No spark. Check gap

1695196 For Prestige / 1800 / 2800, Conquest / 1700 / 2700, & Broadmoor / 1600 / 2600 Series Tractors This kit is required when installing front mounted snowthrowers. 2 Installation Instructions Sub-Frame Hitch Early Manual Lift Only (See Instructions) Hydraulic Lift 47 16 28 27 25 33 40 41 39 38 37 36 43 51 42 33 25 29 29 29 28 28 27 50 17 13 11 14 9 12 13 11 19 18 21 20 10 24 23 7 8 9 9 22 15 9 25 49 22 31 30 30 25 27 28 27 33 25 34 32 3 2 1 4 5 6 33 25 28 25 27 26 27 28 35 Front Hole for Doze

No. Description 1695303 P1524E, Snowthrower 1695304 P1524EX, Snowthrower (CE) 1628 Models Mfg. No. Description 1695305 P1628E, Snowthrower 1695306 P1628EX, Snowthrower (CE) 1732 Models Mfg. No. Description 1695307 P1732E, Snowthrower 1695308 P1732EX, Snowthrower (CE) 1738 Models Mfg. No. Description 1695309 P1738E, Snowthrower 1695310 P1738EX, Snowthrower (CE) 1695358 P1738E, Snowthrower 1695359 P1738EX, Snowthrower (CE) 1734900 Revision 01 Rev. Date 8/2007 TP 100-4585-01-LW-SN Table of Contents

1687227 & 1687228 Instructions For 2004 Simplicity 860EI Intermediate Snowthrowers W 1694433, 1694434 Kit Contents: Ref Part No. Qty. Description 1 1721684 1 GEAR CASE, RH 2 7090052 6 WASHER, 1/4” SPLIT LOCK 3 7092129 12 WASHER, FLAT, .268 x .591 4 7091576 6 NUT, HEX, 1/4-20 5 7092125 6 SCREW, HEX, 1/4-20 x 7/8 6 1721676 1 GASKET, GEAR CASE 7 1721685 1 GEAR CASE, LH 8 960625 1 FITTING - PIPE PLUG 4 Figure 1. Contents This kit is to service intermediate snowthrowers. INSTALLATI

Torque the three set screws (B, D) to 9-11 ft. lbs. 2 Gear Case Kit Installation Instructions Assemble Housing 1. Install the side covers (A, Figure 4) and secure with the original hardware. 2. Reinstall the bearings (C), washers, and retaining rings (D) in both side covers. Figure 4. Assemble Housing A. Side Cover B. Housing C. Bearing D. Washers & Retaining Ring Fill Auger Gear Case Oil 1. Remove the fill plug (Figure 5). Fill the gear box with The Dealer Line Winter Weight Worm G

No. Description 1694919 42” Remote Angling Snow Blade 42” Snow Blade 1732529 Revision 01 Rev. Date 02/2007 TP 100-4241-01-AT-SMA Table of Contents Recommended Accessories ..............................1 Safety Rules & Information Genera Warnings ............................................2 Operation on Slopes........................................2 Preparation ......................................................2 Operating Safety..............................................2 Features & Cont

B) EN ® Loosen upper fasteners. ® Remove lower fasteners. ® Carefully lift handle to the operating position while guiding the speed control rod over the tire. ® Make sure Z-fittings are secured in holes of control levers. © Make sure cables are not caught between the upper and lower handle. © Reinstall lower fasteners. Tighten upper and lower fasteners securely. ® Use the supplied ties to secure the EZ Turn cable (if equipped) to the left handle. FR ® Desserrez les fixations supérieure

Attach the support clamp (C, Figure 2) and hook assembly (B) to the hitch. Secure with four 5/16-18 x 1 carriage bolts (A), washers (D), lockwashers (E), and nuts (F). Do not tighten the hardware at this time. Figure 2. Install Support Clamp A. 5/16-18 x 1 Carriage Bolt D. 11/32 Washer B. Hook Assembly E. 5/16 Lockwasher C. Support Clamp F. 5/16-18 Nut B C D E A F Conquest / 1700 / 2700 & Prestige / 1800 / 2800 Series B C D E A F Broadmoor / 1600 / 2600 Series Assemble Push Bar Latch 1. Attach P

. 19. Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition. EMISSIONS 1. Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth defects, or other reproductive harm. 2. If available, look for the relevant Emissions Durability Period and Air Index information on the engine emissions label. IGNITION SYSTEM 1. This spark ignition system complies with Canadian ICES-002. 5 6

WARNING Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. When starting the engine, ensure that spark plug, muffler, fuel cap and air cleaner are in place and secured. Do not crank engine with spark plug removed. If engine floods, set choke (if equipped) to open/run position. WARNING Engines give off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause nausea, fainting or death. When starting the