inches 1 inch = 25.4 mm 25 26 REPAIR PARTS DRIVE SNOW THROWER - - MODEL NO. 1027STE (HL1027STEA), PRODUCT NO. 954 63 35-45 35 33 15 41 22 34 29 22 31 26 7 2 43 2 11 3 3 25 24 23 12 32 27 44 20 21 21 22 16 17 1 15 2 1 4 13 4 2 1 5 3 2 4 5 3 3 5 1 2 3 13 1 5 2 7 8 9 10 6 3 3 41 14 2 19 18 28 30 40 39 38 36 37 33 REPAIR PARTS DRIVE SNOW THROWER - - MODEL NO. 1027STE (HL1027STEA), PRODUCT NO. 954 63 35-45 KEY PART NO. NO. DESCRIPTION 1 532 14 63-15 Screw, Hex Head 5/16-18 x 3/4 2 873 80 05-00 Nut, L

CHOKE ENGINE OIL GAS O LINE CONTROL FILL CAP / DIPSTICK FILLER CAP NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT. 12 FIG. 20 OPERATION TO START ENGINE Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current. • Be sure your house is a 120 Volt A.C. three-wire groun

4. Connect spark plug wire to spark plug. IMPELLER SHEAR BOLTS The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are de signed to break, preventing damage to any other compo nents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts: AUGER SHAFT 1/4-20 x 2 SHOULDER / SHEAR BOLT 1/4-20 LOC

NO. DESCRIPTION 1 532 18 33-34 Knob, Lever 2 817 50 10-10 Screw #10-24 x 5/8 3 532 17 86-74 Control Assembly, Defl ector 4 873 80 06-00 Nut, Lock 3/8-16 5 819 13 13-16 Washer, Flat 3/8 6 532 17 86-59 Control Assembly, Chute Rotater 7 532 18 40-89 Support, Pivot 8 532 15 00-78 Screw, Hex Head 5/16-18 x 3/4 9 532 18 45-05 Spring, Deflector 10 532 17 98-29 Bolt, Shoulder 11 532 17 92-46 Washer, Flat 1/4 12 873 80 04-00 Nut, Lock 1/4-20 13 872 25 05-05 Bolt, Carriage 5/16-18 14 873 80 05-00 Nut, Loc

12. Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse. 13. Disengage power to the collector/impeller when snow thrower is transported or not in use. 14. Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs). 15. Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles.

To avoid possible freeze-up of the starter, proceed as follows: ELECTRIC STARTER 1. Connect the power cord to the engine. 2. Plug the other end of the power cord into a three-hole grounded 120 Volt A.C. receptacle. 3. While the engine is running, push starter button and spin the starter for several seconds. NOTE: The unusual sound made while starter is spinning will not harm the engine or starter. 4. Disconnect the power cord from the receptacle first, then from the engine. RECOIL STARTER 1. Whi

ENGINE See engine manual. LUBRICATION Use only high quality detergent oil rated with API service classification SG–SL. Select the oil's SAE viscosity grade according to your expected operating temperature. NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil

Allow the engine to warm up for a few minutes. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the OFF position. DO NOT push the primer. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. IF RECOIL STARTER HAS FROZEN If the recoil starter has frozen and will not turn the engine, proceed as follows: 1. Grasp the recoil starter handle and slowly p

1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. KEY PART NO. NO. DESCRIPTION 1 2 3 4 6 6 7 8 7 8 8 9 9 5 5 10 10 01.08.011-A 1 532 42 17-08 PLOW HANDLE LH 2 532 42 17-09 PLOW HANDLE RH 3 532 19 69-44 PANEL BRACKET LH 4 532 19 69-43 PANEL BRACKET RH 5 532 41 45-1

inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. KEY PART NO. NO. DESCRIPTION REPAIR PARTS DRIVE SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 2 2 1 3 4 5 6 7 8 9 10 11 12 13 14 13 14 12 11 10 9 8 7 6 5 4 3 1 2 2 23 17 20 19 16 18 24 22 23 21 22 17 18 15 16 20 19 21 01.15.001-A 1 532 40 51-61 COVER 2 532 18 44-71 SHOULDER SCRE