Assessments - 5, GPA: 4.2
(
)
)
|
Facilidade de uso
Placement should be close enough to the windshield so the antenna may be mounted to the windshield glass, using the supplied double-sided tape. DO NOT ALTER THE LENGTH OF ANTENNA WIRE MOUNTING LOCATIONS: DO NOT MOUNT ALARM CONTROL MODULE IN ENGINE COMPARTMENT UNDERDASH MOUNTING: If locating the control module underdash, the unit should be placed as high as possible, not easily accessible by an intruder. DRIVER'S SIDE underdash mounting provides easy location for wiring, BUT this side usually is a common location where thieves would look for a unit. ALSO, the left side of the dash has more metal and wiring which could cause decreased remote control range. ALWAYS PLACE UNIT AS HIGH AS IS POSSIBLE FOR BEST CONCEALMENT AND OPERATING RANGE PASSENGER SIDE underdash mounting is often the best location for operating range and concealment. Removing the glove box often reveals excellent mounting locations for the control board. Extra wiring may be required to route wiring across the dash area. UNDERSEAT MOUNTING: This location may be used, however it may not be an advantage for the following reasons: 1) This area may be to far away from a glass surface to mount the pager/remote antenna system. 2) The control unit can be exposed to excessive moisture from water and spilled drinks. This moisture stays in the carpet padding causing corrosion to the circuit board which is not cover by our warranty MOUNTING COMPONENTS SIREN MOUNTING Mount Siren as high as possible so as not be accessible outside or underneath the vehicle. Make sure siren is mounted so that it points downward to prevent water from accumulating inside the cone DO NOT MOUNT NEAR EXHAUST MANIFOLD OR ANY OTHER EXCESSIVE HEAT SOURCE LED MOUNTING LED should be located in a visible location on the dashboard or console. Many vehicles now have small knockout panels which provide excellent locations for LED's. DRILL A 15/64” HOLE IN CHOSEN LOCATION, route LED wires through hole and press LED firmly in place. EMERGENCY DISARM/VALET SWITCH MOUNTING This switch is multi-purpose. It is used for emergency override, valet and programming. Mount switch m passenger compartment in a hidden location The user MUST be able to access this switch in an emergency DRILL A 15/64" HOLE IN CHOSEN LOCATION. When mounting the switch, make certain there is enough room on the back side so that the switch wires will not accidentally short out on any metal. Use the supplied nuts and washers to secure the switch in place Prime SECURITY PRODUCTS, INC. SVM»EiU»AGE™ CS-9705FM FM HIGH-FREQUENCY PAGER & REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATION INSTRUCTIONS INTRODUCTION This system features an ultra-compact, FM hand-held transceiver that incorporates bolh a pager and remote control and fits comfortably in the palm of your hand. The pager section uses a high-frequency design to provide long range(up to 1 mile) and excellent penetration performance, even in difficult reception areas such as shopping malls and underground garages. There are two types of features of the system: Primary. These features MUST BE CONNECTED for proper system operation Optional: These features connected only if wanted All optional features are marked "OPTIONAL" As the installation progresses you may connect any ‘Optional" features of the system. Optional features are listed with primary features only when they effect the operation of the primary feature. We hope this brief introduction helps eliminate confusion when installing your system. Should you experience trouble during installation, tech support is available by calling: 1 (800) 998-6880 Monday - Friday 8:00am - 4:30pm Pacific Time This device complies with FCC Rules part 15 Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) th:s device must accept any interference that may be received, including interference that may cause undesired operation The manufacturer is not responsible for any radio or TV interference cajseo by unauthorized modifications to this equipment Such modification cojld void the user's authority to use tne equipment MOUNTING COMPONENTS SHOCK SENSOR MOUNTING DO NOT MOUNT SHOCK SENSOR IN ENGINE COMPARTMENT, the sensor is not environmentally sealed and will eventually fail to operate. Mount Shock Sensor under the dash board in a location which is hidden from direct view, but accessible for adjustment Recommended Mounting locations include: Dashboard Support Strut Steering Wheel Column Underdash Wire Harness Interior Firewall Heater/Air Conditioning Box/Ducting These are only recommendations There may be other locations or positions that may be better suited to your application Some of the locations above will provide better sensitivity than others depending on your particular vehicle, and what you are most interested in protecting. DO NOT MOUNT SENSOR TO ANY PANEL THAT WILL DETECT RELAY CLICKING OR RESONATE FROM SIRENS OR THERMOSTATIC C...