Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
If your King-Dome does not operate as outlined in this manual please call King Controls at ( 800) 982-9920 or visit our website at TABLE OF CONTENTS Section Contents Page 1. INTRODUCTION.....................................................................................2 2. DEFINITION OF TERMS ........................................................................3 3. INSTALLATION..................................................................................4-10 4. OPERATION ....................................................................................11-15 5. STORE/RECALL POSITIONS ..............................................................16 6. DIAGNOSTICS .....................................................................................17 7. MAINTENANCE ....................................................................................18 8. LIMITED WARRANTY ..........................................................................19 DIRECTV is a registered trademark of DIRECTV, Inc. Dish Network® is an official trademark of Echostar Communications Corporation. Bell ExpressVu® is an official trademark of Bell Canada. DVB® is a trademark of the DVB Digital Video Broadcast Project (1991-1996) Page 1 SECTION 1 INTRODUCTION The King-Dome AutoScan Satellite System includes 2 main components (Fig. 1). Dome (Antenna) Unit Located on the roof of the vehicle. The dish is covered by a protective dome that keeps operational components free from the elements. Controller Located in the vehicle. Used to activate the system, position the dish, and access diagnostic information. Note: A TV, satellite receiver, and program subscription are also required for satellite TV viewing. (Not supplied by King Controls.) Fig. 1 Page 2 SECTION 2 DEFINITION OF TERMS AZIMUTH: Circular rotation around the vehicle. (like a clock face: front of vehicle is 12:00, rear is 6:00) (Fig. 2) Fig. 2 ELEVATION: Angle in degrees measured from the ground plane (Fig. 3). Fig. 3 SIGNAL STRENGTH: Intensity of electronic signal received from the satellite transmission. Page 3 SECTION 3 INSTALLATION TOOLS AND MATERIALS REQUIRED: -drill and drill bit set - tape measure -7/16” open end wrench (coax connections) - adhesive sealant (compatible with roof material) - appropriate fasteners to install all components and wiring - 5/32” allen wrench, channel lock or pliers (to remove shipping bolts) -wire cutter (to remove shipping tie strap) KIT CONTENTS: 1. Unpack and identify all components (Fig. 4). Fig. 4 KING CONTROLS KING DOME OPERATING INSTRUCTIONS 1. Turn on TV 2. Go to signal meter screen and choose transponder number for dish or direct tv. 3. Enter local zip code on signal meter screen to determine satellite elevation.. 4. Press UP arrow to turn King Dome on. 5. Press UP or DOWN arrow to display dish elevator and match to elevation on signal meter screen on tv. 6. Press and hold RIGHT arrow for 10 seconds. Dish will perform a 360 degree scan for satellite. When signal strength appears on tv, press ANY BUTTON to stop dish from rotating. 7. Press the UP, DOWN, RIGHT or LEFT arrows to fine tune signal strength to the highest possible number on tv signal meter screen. KING-DOME Page 4 IMPORTANT! The tie strap and spacer, and the bolts and washers must be removed from the bottom of the dome unit prior to installation. DO NOT REMOVE THE DOME COVER TO REMOVE THESE SHIPPING RESTRAINTS. YOU MUST PLUG THE SHIPPING BOLT HOLES WITH THE SUPPLIED PLUGS (ATTACHED TO TIE STRAP SHIPPING RESTRAINT). 2. Remove and discard the tie strap and spacer (KEEP RUBBER PLUGS), and the (2) bolts and (2) washers that pass through the bottom of the base (Fig. 5). 3. Insert provided plugs into holes that were occupied by the shipping bolts. Inserted plugs should be flush with base (Fig. 5). Fig. 5 IMPORTANT! Remove and discard Tie Strap and Plastic Spacer prior to installation. KEEP RUBBER PLUGS. IMPORTANT! Remove and discard Bolts and Washers prior to installation. IMPORTANT! After removing shipping bolts, firmly insert plugs into holes. Plugs should be flush with base. Page 5 DOME LOCATION 4. Select an area on the roof for the dome unit and the location where the wiring will enter the vehicle through the roof to the satellite receiver, controller, and 12 volt power source inside, using the following criteria: a) The shortest distance between the dome unit and the satellite receiver is most desirable. b) The dome unit requires a 28 inch diameter mounting area. c) The dome unit must be mounted on the centerline of the vehicle. Mounting off centerline reduces electronic level compensation. d) There must be no “line of sight” obstructions. Air conditioning units, other antennas, and storage areas that are too close to the dome unit may prevent the satellite signal from reaching the dish (Fig. 6). HEIGHT OF OBSTRUCTION APPROXIMATE MINIMUM DISTANCE TO DOME EDGE 10” 8” 11” 10” 12” 12” 13” 14” 14” 16” 15” 18” 16” 20” Fig.6 IMPORTANT! For installations...
Este manual também é adequado para os modelos :Receptor de Satélite - 9630 LP (1.07 mb)