Assessments - 1, GPA: 3 ( )

Fabricante : Winegard Arquivo Tamanho: 1.17 mb Arquivo Nome : Língua de Ensino:

The directional handle and threaded rod will fit roofs up to 5-1/4” thick. If you are using wedges to compensate for roof/cceiling slope, be sure to allow for this extra thickness. You may add an extension to the directional handle for thicker roofs. Each extension will increase the length of the directional handle by 2-1/4”. Figure 11 FIGURE 11 STEP 16. Press the directional handle onto the hub. Point arrow on the directional handle towards the rotate/lock lever to orient to the splines. STEP 17. Install the washer and nut on the threaded rod. Tighten the nut enough to snug the directional handle to the hub. STEP 18. IF YOU ARE USING AN EXTENSION, adjust the total length of the directional handle and extension by cutting the directional handle. After adjusting parts for proper roof thickness, glue the extension to the directional handle. Use ABS (plastic pipe) glue. NOTE: For roofs over 5%” thick, a longer aluminum hex shaft is needed. Contact Winegard for this part. CUTTING SHAFT LENGTH Flip down handle on the elevating crank handle. Slide elevating crank handle up shaft until snug against the directional handle. Mark the elevating shaft at the inside bottom surface of crank handle housing, Figure 13. After removing crank handle, cut shaft at mark. Reinstall crank. FIGURE 13 Elevating Shaft Cut Elevating Shaft at inside surface of crank handle housing; shaft goes through hex-shaped opening by screw. 8 CAUTION! After INITIAL INSTALLATION. the antenna SHOULD ROTATE APPROXIMATELY 360° FROM TRAVEL POSITION. The pointer on the DIRECTIONAL HANDLE should point towards the RED SCREW ON THE ROTATION CLAMP when in the TRAVEL POSITION. FIGURE 15 FIGURE 14 ASSEMBLED VIEW Rotation Clamp Red Screw Pointer must point to RED SCREW at CENTER OF ROTATION CLAMP when in travel position. POINT TO BACK OF RV CAUTION! The antenna MUST BE IN THE TRAVEL POSITION before aligning the directional handle and ceiling plate! FIGURE 16 Elevating Shaft Threaded Tube Directional Handle Extension Ceiling Plate (4) #10 Phillips Flat Head Screws Directional Handle ALIGN POINTER WITH ANTENNA TRAVEL POSITION Elevating Crank Handle (When installed, extends 2-1/4” from ceiling.) Snap Handle into base when not in use. TIGHTEN SCREW SNUGLY! 9 Digital Elevation Sensor Interior Wallplate 0 STEP 19. See Figure 17. If using the SM-1000 surface mount box, feed cable through hole in box. STEP 20. Connect wires coming from sensor on roof to wall plate display in vehicle. It is important to properly connect the wires at the roof and the wall plate. (Plug will click when inserted properly.) The system is designed to use a 9 volt battery OR +12 VDC from vehicle. Do not use both! IMPROPER WIRING WILL CAUSE DAMAGE TO THE PRODUCT, SEE FIGURE 18. SM-1000 Surface Mount Box STEP 21. Pressing the button when the antenna is in a vertical position should display 24 (±1°). Display will automatically turn off after 1 minute. STEP 22. Check connectors and cable entry points. Be sure these areas are properly sealed to prevent water damage. FIGURE 18 Snap battery in place, making sure battery terminals are firmly seated on wall plate terminals. FIGURE 17 Based on 5 minutes a day of usage, standard new alkaline batteries should last 88 days. OPERATION (Also on pages 2-3) STEP 23. Using satellite receiver, find correct elevation for your location. See the receiver manual for details of setup information. STEP 24. Press button on Winegard digital display wall plate. If antenna is in travel position, the display will show LL for Low Limit. Cable and plug from roof sensor unit; plugs into sensor STEP 25. Crank elevation handle to raise antenna. Stop when readout displays correct elevation for your location. (Found on receiver setup menu.) STEP 26. Rotate antenna VERY SLOWLY until correct satellite signal is acquired. Note: 3° and stop. DO NOT rotate continuosly even if you’re rotating slowly. If the elevation angle has changed, it could be due to the following — • Vehicle is not parked level. • Antenna system mounted on slightly sloped roof. If this is the reason, after you have rotated the antenna to the approximately correct compass direction, adjust to correct elevation and continue research. Special Note: When you have found the satellite signal, adjust the antenna u/down and right/left for the strongest signat your receiver displays. due to variation in receivers and installation methods, you may find the elevation numbers after peaking on strongest signal no long match what the receiver display recommended. This is normal. The elevation sensor should always get your close enough to pick up a signal to peak on. If display turns off while you’re searching, just push the button for another minute of operation. Whith a little practice, most users find the signal in 30 to 50 seconds. 10 Parts List 11 Parts List 12 Parts Views INTERIOR HARDWARE KIT RK-CEIL Ceiling Base Directional Dial (4) #10 Phillip Fla...

Baixe o seu

Para fazer o download, introduza 2 dígitos :