Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
54-0157 Rev.J 2-21 A Guide to TracVision R5/R4 A Guide to TracVision R5/R4 The following is an example of configuring the fictional YOURSAT 101 as the USER1 configured satellite. Prior to configuring this satellite or any others, be certain to get the most up-to-date information from one of the sources previously discussed. Table 2-5 Sample User-defined Satellite Configuration (Europe) YOURSAT 101 at 71 West, DVB decoder, Circular Polarization LNB Horizontal High Frequency 11.966 GHz Symbol Rate 27500 FEC Code 3/4 Network ID 2048 (dec) = 0x0800 Vertical High Frequency 11.823 GHz Symbol Rate 27500 FEC Code 3/4 Network ID 2048(dec) = 0x0800 Vertical Low Data Listed Horizontal Low No Data Listed Example: Based on this information, the data entered via the PC would look like this, assuming that YOURSAT 101 would be Satellite A: SATCONFIG,USER1,7,W,3,L @DEBUGON @SATCONFIG,A,98,11966,27500,34,0x0800,H,H,3 @SATCONFIG,A,98,11823,27500,34,0x0800,V,H,3 @SATCONFIG,A,98,00000,27500,34,0x0000,V,L,3 @SATCONFIG,A,98,00000,27500,34,0x0000,H,L,3 @SAVE,A @DEBUGOFF ZAP Installation Installation The following is an example of configuring the fictional YOURSAT 101 as the USER1 configured satellite. Prior to configuring this satellite or any others, be certain to get the most up-to-date information from one of the sources previously discussed. Table 2-6 Sample User-defined Satellite Configuration (North America) YOURSAT 101 at 71 West, DVB decoder, Circular Polarization LNB Right Frequency 11.966 GHz Symbol Rate 27500 FEC Code 3/4 Network ID 2048 (dec) = 0x0800 Left Frequency 11.823 GHz Symbol Rate 27500 FEC Code 3/4 Network ID 2048(dec) = 0x0800 Example: Based on this information, the data entered via the PC would look like this, assuming that YOURSAT 101 would be Satellite A: SATCONFIG,USER1,71,W,3,C @DEBUGON @SATCONFIG,A,98,11966,27500,34,0x0800,R,U,3 @SATCONFIG,A,98,11823,27500,34,0x0800,L,U,3 @SAVE,A @DEBUGOFF ZAP 54-0157 Rev.J 2-23 A Guide to TracVision R5/R4 A Guide to TracVision R5/R4 Approximate Latitude/Longitude Grid # Latitude Longitude 2.6 Setting the Skew Angle (European Systems Only) The Antenna LNB skew angle must be adjusted to optimize channel reception. Refer to your satellite service provider for the proper skew angle for the selected satellite service and geographical location. The skew angle for satellites in the KVH library can also be obtained by entering your latitude and longitude into the antenna. Determine your grid number in Figure 2-18 to find your corresponding latitude and longitude listed in Table 2-7. Figure 2-18 European Position Grid 1 67.N 7.W 2 67.N 7.E 3 67.N 22.E 4 65.N 45.E 5 63.N 7.W 6 63.N 7.E 7 63.N 22.E 8 57.N 7.W 9 57.N 7.E 10 57.N 22.E 11 55.N 40.E 12 53.N 7.W 13 53.N 7.E 14 50.N 22.E 15 47.N 7.W 16 47.N 7.E 17 43.N 7.W 18 43.N 7.E 19 43.N 22.E 20 43.N 37.E 21 36.N 7.W 22 36.N 7.E 23 36.N 22.E 24 36.N 37.E 1 2 3 4 11 765 8 9 10 12 13 14 1615 17 18 19 20 21 22 23 24 Installation Installation 1. Type HALT then press Enter. 2. Type DEBUGON then press Enter. 3. Type the following command (see the Key below) then press Enter. GPS,XX,D,YYY,E Key: XX = latitude (0 - 90) D = S (South) or N (North) YYY = longitude (0 - 180) E = E (East) or W (West) 4. Type SKEWANGLE then press Enter. The system will respond with the skew angle for whichever satellite is currently selected. Adjusting the LNB Skew Angle 1. Determine the skew angle for the selected satellite and region. 2. Loosen the wing nut on the LNB clamp so that the LNB can be moved (see Figure 2-19). Figure 2-19 LNB Skew Angle Adjustment Skew Angles LNB Clamp & Wing Screw Scribe Mark LNB 30 30 3. Carefully rotate the LNB so that the scribe mark on the LNB clamp is aligned with the proper angle measurement. 4. Tighten the wing nut and LNB clamp to secure the LNB. 54-0157 Rev.J 2-25 A Guide to TracVision R5/R4 A Guide to TracVision R5/R4 Testing the System Now all you need to do is turn the system on and ensure everything works properly. Follow the steps below to test the TracVision system. 1. Park the vehicle in a blockage-free area. The antenna requires an unobstructed view of the southern sky to receive satellite signals. 2. Turn on the receiver(s) and TV(s). For instructions on operating the receiver, refer to the receiver’s User’s Manual. 3. Turn on the TracVision antenna. 4. Within a few minutes, a picture should appear on the TV. 5. (TracVision R5 only) Take a road test and verify that the antenna tracks the satellite while the vehicle is moving. 6. When you have finished testing, shut down the system. Installation Installation 8 Configuring TracVision R5/R4 for Remote Satellite Dish Operation In some campground locations, dense foliage will block the satellite signal. In these situations, a remote portable antenna may be the only solution to satellite signal reception. The wiring option for the remote dish is very simple and should be installed when the TracVision R5/R4 is installed. A high- quality “A/B switch” should be used to ch...