** If GPS is providing valid position data to the antenna, manual entry of latitude/longitude is not available. ** 2005, KVH Industries, Inc. Welcome to TracVision G8 Welcome to TracVision G8 Owner’s Manual This manual provides detailed instructions on the proper operation, installation, configuration, troubleshooting, and maintenance of the KVH TracVision G8 satellite TV system. For operation instructions, refer to the Guide to Operation. For installation, configuration, troubleshooting, and ma
Complete details regarding connecting TracVision G4 Gyro P o w er Ground Gyro RXD+ Gyro RXD- Gyro TXD- Gyro TXD+ Not Used IRD Ground Wire (to IRD) TracVision G4 can either receive power through the ADCU (as illustrated in the diagram) or directly from ship’s power if that is more convenient. Refer to "Alter nate Method of Pro viding P o w er to the Antenna" on page 32 for details. to ship's power have been provided in "Connecting the ADCU to Vessel Power" on page 37. Wiring Color Code Definition
With hundreds of channels of digital-quality TV and music to enjoy, traveling will never be the same! This User’s Guide provides all of the basic information you need to use the system’s receiver and receive the DIRECTV satellite entertainment you want. For detailed installation information, please refer to the TracVision Installation Guide. KVH Part # 54-0287 Rev. A © 2005 KVH Industries, Inc., All rights reserved. TracVision Receiver User’s Guide TracVision Receiver User’s Guide KVH ® and Trac
3. Remove the PCB cover and set aside. 106 54-0147 Replacing the Main PCB Replacing the Main PCB . With a PC connected to the ADCU’s maintenance port, apply power to the antenna unit. 2. Record the system serial number for later re-entry (the serial number is listed at the beginning of the startup sequence, as shown in Appendix F on page 143). 3. Disconnect power from the antenna unit and the IRD. 4. Remove the PCB cover, as explained in “Removing the Main PCB Cover” on page 106. 5. Disconnect a
KVH® Industries’ TracVision® R5/R4 is designed for use with European and North American DVB-compatible satellite services as well as DIRECTV®. This manual provides detailed instructions on the proper installation, use, and maintenance of your TracVision R5/R4 system. Before using this manual, be sure to check for any addenda, which might detail changes to the manual’s information. Throughout this manual, important information is marked for your attention by these icons: A helpful tip that either
1.3 Materials Provided with TracVision C3 The data/power cable supplied with the system is 28 ft (8.5 m) in length. The RF cable supplied with the system is 50 ft (15 m) in length. Table 1-3 has been updated to show the correct cable lengths. Component KVH Part No. Table 1-3 Antenna Unit (comprising): 01-0225-20† 01-0225-23†† 01-0225-26††† 01-0225-29†††† TracVision C3 Packing List Baseplate Assembly 02-1245-01* 02-1245-03** Radome Assembly 02-0953-04 RF Cable (50 ft/15 m) Data/Power Cable (28 ft
Who Should Install the System? To ensure a safe and effective installation, KVH recommends that a KVH-authorized marine technician install the TracVision M3 system. To find a technician near you, go to If you purchased the product and decide to install it yourself, please see the enclosed warranty statement for warranty implications. Important Safety Precaution CAUTION DO NOT apply power to the TracVision antenna with the radome removed because the antenna has moving parts that can cause injury.
* DiSEqC applies to European systems only 3. Turn on the antenna using the switchplate, as pictured in Figure 3-2. 4. (TracVision L3 only) If the vehicle is moving, avoid turning the vehicle for 60 seconds after turning on the antenna to allow the antenna gyro to initialize properly. 3.2 Changing Channels and Switching Between Satellites If you have followed the installation instructions, your system should be set to the active satellite pair of your choice and the system should have downloaded
TracVision S3 is designed to operate only while your vehicle is parked. Using Your TracVision L3/S3 When Parked When your vehicle is stopped, it is not necessary for the TracVision L3/S3 to be turned on. After parking your vehicle and confirming that the antenna is receiving the satellite signal, you may turn off the TracVision L3/S3 unit to avoid unnecessary use of power. Because the LNB receives its power from the IRD, the antenna will continue to receive the satellite TV signals and relay the
86 54-0166 Maintenance Port Parser Commands Maintenance Port Parser Commands Set RF Tracking Parameters Function: sets RF tracking parameter Command: @SATCONFIG,X,N,F,S,C,ID,P,B,D