Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
Mill/Drill Coarse Downfeed Handle 26. Mill/Drill Head Fine Downfeed Knob 27. Mill/Drill High/Low Speed Selection Lever 28. Mill/Drill Variable Speed Adjustment Knob 29. Mill/Drill Power Indicator Light 30. Mill/Drill ON/OFF, Emergency Stop Switch G0516 Lathe/Mill 1 2 3 4 5 6 7 9 10 11 13 14 15 12 8 1 2 3 4 5 6 7 9 10 11 13 14 15 12 8 Figure 3. The picture above shows important accessories and tools that are included with the Model G0516. Please take some time to identify these items. Similar to the components and controls in Figure 2, these items are mentioned throughout the manual and knowing them is essential to understanding the instructions and terminology used in this manual. 1. 3-Jaw Chuck 9. Tailstock Dead Center 2. 3-Jaw Chuck Key 10. Headstock Dead Center 3. 4-Jaw Chuck 11. Drill Chuck 4. 4-Jaw Chuck Key 12. Drill Chuck Arbor 5. Faceplate 13. Spanner Wrench 6. Turret Tool Post 14. Drill Chuck Key 7. Square Head Wrench 15. Fixed-Shaft Gear 40T 8. Milling Table G0516 Lathe/Mill -9 SECTION 5: SET-UP Unpacking This combination lathe/mill is shipped from the manufacturer in a carefully packed crate. If you discover the machine is damaged after you’ve signed for delivery, and the truck and driver are gone, you will need to file a freight claim with the carrier. Save the containers and all packing materials for possible inspection by the carrier or its agent. Without the packing materials, filing a freight claim can be difficult. If you need assistance determining whether you need to file a freight claim, or with the procedure to file one, please contact our Customer Service. The Model G0516 is a heavy machine, 420 lbs. shipping weight. DO NOT move the machine by yourself – you will need assistance and power equipment. Serious personal injury may occur if safe moving methods are not followed. Some metal parts may have sharp edges on them after they are formed. Please examine the edges of all metal parts before handling them. Failure to do so could result in injury. When you are completely satisfied with the condition of your shipment, you should inventory its parts. Piece Inventory Inside the crate you will find: • Model G0516 Base Unit • Mill/Drill Attachment • Backsplash • 6mm Allen® Wrench • 5mm Allen® Wrench • 4mm Allen® Wrench • 3mm Allen® Wrench • 75T Gear • 72T Gear • 70T Gears (2) • 68T Gear • 66T Gear • 60T Gear • 50T Gear • 48T Gear • 45T Gear • 40T Gear • Fixed-Shaft Gear 40T • Lathe Chuck Key • 5.5/7mm Combo Wrench • 8/10mm Combo Wrench • 12/14mm Combo Wrench • 17/19mm Combo Wrench • 36mm Wrench • Drill Chuck Key • 3 Outside Jaws • Dead Center MT#2 • Dead Center MT#3 • Spanner Wrench • 19mm T-Handle Wrench • Square Head Wrench • Oil Can • Taper Shank MT#3 & Drill Chuck • T-Nut • Mill/Drill Table • Cap Screws M8-1.25 x 25 (4) • Mill/Drill Fuse 110V/5A • Lathe Fuse 110V/25A • Carriage Handle & Screw • Apron Handle & Screw • Faceplate • 4-Jaw Chuck w/Flange • Fixing Pin -10-G0516 Lathe/Mill Hardware Recognition Chart G0516 Lathe/Mill -11- 5mm 10mm 15mm 20mm 25mm 30mm 35mm 40mm 45mm 50mm 55mm 60mm 65mm 70mm 75mm Washer Lock Washer Hex Nut Wing Nut Phillips Head Sheet Metal ScrewSetscrew Phillips Head Screw Thumb Screw Slotted Screw Countersunk Phillips Head Screw Cap Screw Carriage Bolt Hex Head Bolt Button Head Screw Flange Bolt Phillips Head Hex Bolt Lock Nut 5.16''1.4'' 3.8'' 1.2'' 5.8'' 7.16'' 9.16'' 3.4'' 7.8'' 1'' 11.4'' 11.2'' 13.4'' 2 21.4'' 21.2'' 23.4'' 3 LINES ARE 1MM APARTLINES ARE 1 . 16'' INCH APART 5.8''WASHER DIAMETER 9.16'' WASHERDIAMETER 1.2'' WASHERDIAMETER 12mmWASHERDIAMETER 10mmWASHERDIAMETER 7.16'' WASHERDIAMETER 8mm WASHERDIAMETER 3.8'' WASHERDIAMETER 5.16'' WASHERDIAMETER 1.4'' WASHERDIAMETER #10 WASHERDIAMETER 4mm WASHERDIAMETER 6mm WASHERDIAMETERWASHERS ARE MEASURED BY THE INSIDE BOLT DIAMETER BY PLACING INSIDE CIRCLE#10 1.4'' 5.16'' 3.8'' 7.16'' 1.2'' 5.8'' 4mm 6mm 8mm 10mm 12mm 16mm Use this chart to match up hardware pieces during the assembly process! Clean Up The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thoroughly, some parts may need to be removed. For optimum performance from your machine, make sure you clean all moving parts or sliding contact surfaces that are coated. Avoid chlorine- based solvents as they may damage painted surfaces should they come in contact. Always follow the manufacturer’s instructions when using any type of cleaning product. Do not use gasoline or other petroleum-based solvents to clean with. They have low flash points which make them extremely flammable. A risk of explosion and burning exists if these products are used. Do not smoke while using solvents. A risk of explo- sion or fire exists and may result in serious personal injury. Many of the solvents commonly used to clean machinery can be toxic when inhaled or ingested. Always work in well- ventilated areas far ...