Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
Remove any adjusting key or c. wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. Do not overreach. Keep proper d. footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose e. clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. If devices are provided for the conf. nection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust-related hazards. Power tool use and care4. Do not force the power tool. Use a. the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power tool if the b. switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the c. power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the d. reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Maintain power tools. Check for e. misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and f. clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use the power tool, accessories g. and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. Service6. Have your power tool serviced by a. a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Lathe Safety Warnings Maintain labels and nameplates on 1. the Lathe. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Do not run the Lathe without its cov2. ers and guards in place. Tighten all locks before operating.3. Do not mount a split workpiece.4. Use the lowest speed when starting a 5. new workpiece. Always stop the Lathe at its slow6. est speed. If the Lathe is run so fast that it vibrates, there is a risk that the workpiece will be thrown or the cutting tool jerked from your hands. Always rotate the workpiece by hand 7. before turning on the Lathe. If the workpiece strikes the tool rest, it could split and be thrown out of the Lathe. Do not allow cutting tools to bite into 8. the workpiece. The wood could be split or thrown from the Lathe. Always position the tool rest above 9. the centerline of the Lathe when shaping a piece of stock. Before attaching a workpiece to the 10. faceplate, always rough it out to make it as round as possible. This minimizes the vibrations while the piece is being turned. Always fasten the workpiece securely to the faceplate. Failure to do so could result in the workpiece being thrown away from the Lathe. Remove all loose knots in the work11. piece before mounting between the centers or on the faceplate. Position your hands so they will not 12. slip onto the workpiece when the Lathe is running. Use a brush or compressed air to 13. remove wood shavings; never your hands. The wood shavings will be sharp. Avoid unintentional starting. Prepare 14. to begin work before turning on the tool. Do not reach across the Lathe while it 15. is running. Industrial applications must follow 16. OSHA guidelines. Do not use the Lathe if it is off-bal17. ance, or the workpiece is not properly centered. Only feed workpiece into a cutting 18. tool against the direction of rotation. The workpiece must always be rotating toward you. Do not leave the tool unattended 19. when it is plugged into an electrical outlet. Turn off the tool, and unplug it from its electrical outlet before leaving. This product is not a toy. Keep it out 20. of reach of children. People with pacemakers should 21. consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. In addition, people with pacemakers should: • Avoid operating alone. • Do not use with power switch locked on. • Properly maintain and inspect to avoid electrical shock. • Any power cord must be properly grounded. Ground Fault Circuit Interrupter (GFCI) should also be implemented ...