3. Move the point of skew to the right half of the desired width of your cut, see Figure 19. 4. With the bevel parallel to the right side of the cut, raise the handle and push the tool in to the desired depth. 5. Repeat from the left side. The two cuts should meet at the bottom and leave a clean "V" cut. 6. Additional cuts may be taken to add to either the depth or width of the cut. Parting 1. Place the parting tool on the tool rest and raise the handle until it starts to cut and continue to cut

If in doubt, use the next heavier gauge. Remember, the smaller the gauge number, the heavier the cord. Volts Total Length of Cord in Feet 120V 25 50 100 150 AWG 12-16 Amps 14 12 Not Recommended 5 230 Volt Operation If 230V, single-phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This lathe is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 2

BD920N-CS09......... .........Rivet............................................... ..................2x5................ ...........2 10 ... 5020......................... .........Graduated Ring.............................. ...........1 11... ... BD920N-CS11......... .........Key................................................. ..................3x13.............. ............1 12... ...5023......................... .........Spring............................................. ............1

1 29........ JWL1642-129 ...............Plate...................................................... ............................................... 1 ........JWL1642-130...............Digital Readout......................................JWL-1642EVS........................1 ............JWL1642-130A.............Digital Readout......................................JWL-1642EVS-2.....................1 31........ TS-1540011..................Nut ........................................................

This new 10HP ZX Series lathe boasts a 22" swing over bed and comes standard with a 10" 3-jaw chuck with top reversing jaws and a 12" 4-jaw chuck. The 22" ZX Series Large Spindle Bore Lathe comes equipped with a 3-1/8" bore spindle supported by two tapered bearings and one ball bearing and a universal gear box with pitch threads in inches, metric, diametral and module. The universal gear box is dial controlled eliminating the need for changing end gears. The GH-2280ZX also comes standard with a

20) to desired rate. Note: for threading, lever (D) will be set at "C" or "E", depending on desired thread. 3. Push lever (B, Fig. 19) to the right. 4. Engage the half nut lever (C, Fig. 19). 5. To cut inch threads, reference the feed and thread tables. The half nut lever and the threading dial are used to thread in the conventional manner. The thread dial chart specifies at which point a thread can be entered using the threading dial. 6. To cut metric threads, the half nuts must be left continu

This new 3/4HP lathe supports stock up to 12" in diameter and 20" in length. A built-in work light illuminates your work piece while turning and the spindle has a lock and indexing capability for fluting and veining applications. Integrated carry handles and a cord wrap are added for portability. STOCK NO. 900493 10M 07/07 ©2 0 07 WMH TOOL GROUP, Inc. All Rights Reserved. Jettools.com JWL-1220: 12"x20" WOOD LATHE STOCK NUMBER 708376 Model Number JWL-1220 • Heavy-duty cast-iron lathe

This ^ HP lathe supports stock up to 10" in diameter and 14" in length. This lathe features solid cast iron construction, the added convenience of a hollow tailstock, a 6" tool rest and electronic variable speed. The spindle also has a versatile locking/indexing mechanism for fluting and veining applications. rri JET 10"x14" VARIABLE SPEED INDEXING MINI LATHE 10"x14" VARIABLE SPEED INDEXING MINI LATHE • continously variable speed operation from 500-3900 rpm • Heavy-duty cast-iron lathe bed

To order parts or reach our service department, call 1-800-274-6848 between 7:30 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Figure 13 12 JML-1014I Mini Lathe 13 Parts List for JML-1014I Mini Lathe Index No. Part No. Description Size Qty 1............. JML1014-101 .... .....Headstock................................................. ..... 1 2..........

With features like a 25/32" spindle bore, a MT#3 tailstock and 6 spindle speeds you'll be able to turn some surprisingly hefty projects! If you're thinking of making parts for models, engines or even for repairs around the home or shop, this is the jettools.com JET 9" x 20" BELT DRivE BENcH LATHE 4 Way ■ Tool y Post j/ Enclosed Quick Change " Gear Box Adustable Tailstock d 4 L ■ ?- Ü.T Hardened and Ground Bedways Optional Stand 9" x 20" BELT DRivE BENcH LATHE • Spindle suppor