Assessments - 6, GPA: 4
(
)
)
|
Facilidade de uso
Care of Your Washer Use only a damp or sudsy cloth for cleaning the control panel. Some cleaning product sprays may harm the finish on the control panel or damage the interior of the hood. Wipe the washer cabinet as needed. If detergent, bleach or other washing products are spilled on the cabinet, wipe immediately. Some products will cause permanent damage if spilled on the cabinet. Do not use scouring pads or abrasive cleansers. The wash drum and window will need no particular care although they may need rinsing or wiping after an unusual load has been washed. Outside of window can be cleaned with household window cleaner. NOTE: Leave the loading door open to allow the inside of the washer to dry out after use. This helps prevent musty odors from developing. DO NOT allow small children to play on or around the washer. Clean the lint filter before drying each load. The lint filter may be washed if needed. Annually remove lint filter and screw to vacuum the duct under it. Ordinarily, the dryer cylinder will need no care. Wipe the dryer cabinet as needed. If detergent, bleach or other washing products are spilled on the cabinet, wipe immediately. Some products will cause permanent damage if spilled on the cabinet. Use only a damp or sudsy cloth for cleaning the control panel. Some spray prewash products may harm the finish on the control panel. NOTE: The wiring diagram is located inside the control panel. CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. W049 Exhaust System The exhaust duct should be inspected after one year of use and cleaned if necessary by a qualified service person to remove any lint build-up. Inspect and clean exhaust duct every one to two years as required thereafter. The weather hood should be checked frequently to make sure the dampers move freely, dampers are not pushed in and that nothing has been set against them. Keep dryer area clear and free from combustible materials, gasoline and other flammable vapors and liquids. Do not obstruct the flow of combustion and ventilation air. NOTE: Verify proper operation after servicing. 801506 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 23 Maintenance For Energy Conservation . Make sure the lint filter is always clean. . Do not overload dryer. . Do not overdry clothes. . Remove items to be ironed while still damp. . Large loads of similar fabrics dry the most efficiently. However, dry permanent press in smaller loads to prevent wrinkling. . Use the correct temperature FABRIC SELECTOR setting for the type of fabric being dried. . Locate your dryer so the exhaust duct is as short and straight as possible. . Do not open the door during the drying cycle. . Plan to do your laundry on low humidity days; your clothes will dry faster. . Should you plan to dry several loads, do them one after another, then you do not have to reheat the dryer’s interior parts each time. Reinstallation of Shipping Materials Remove front access panel by removing two screws. Place the shock sleeves on all four shock absorbers. Refer to Figure 8. Insert hooked end of shipping brace into the open slot of the motor mount. Attach with bolts and washers. Refer to Figure 8. Reinstall front access panel. Figure 8 Refer to the INSTALLATION INSTRUCTIONS for proper procedures whenever the washer is moved. IMPORTANT: The shipping materials MUST be reinstalled whenever the unit is moved. H336I 1 Shock Sleeves 2 Motor Mount 3 Bolts and Lockwashers 4 Hooked End of Shipping Brace 2 1 4 3 24 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 801506 Maintenance Before You Call for Service You may save time and money by checking the following: If the Washer: Won’t Fill Won’t Start Won’t Tumble Won’t Spin Won’t Drain Possible Reason – Do This to Correct • Be sure power cord is plugged all the way into the electrical outlet. • • • • Close the loading door tightly. • • • • Check the house fuse or circuit breaker. • Turn on the hot and cold water faucets. • Pull timer knob out to start the washer. Check to make sure timer is not set at an OFF position. • Clean the screens in the water mixing valve. • • Are controls properly set? • • Broken drive belt. Call the service person. • • Foreign object trap clogged. Clean foreign object trap. If the Dryer: Does Not Start Does Not Heat Does Not Dry Clothes Satisfactorily Possible Reason – Do This to Correct • Dryers equipped with power cord – Be sure the power cord is plugged all the way into the electrical outlet. • Close the loading door. • Be sure timer is not in COOL DOWN setting or NO HEAT cycle. • Push timer knob in to start dryer. • • (Electric Dryers Only) Has the laundry room fuse(s) blown or become loosened, or are circuit breakers open? The dryer itself does not have an electrical fuse. An electric dryer has an electrical circuit with two fuses. • Has the motor overload protector cycled? Wait 10 minutes and try again. • Is ...