Log:
Assessments - 3, GPA: 4.3 ( )

Instruções de Operação Alliance Laundry Systems, Modelo EC001F

Fabricante : Alliance Laundry Systems
Arquivo Tamanho: 666.79 kb
Arquivo Nome : F232088en.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


SW008 Always disconnect power and water supplies before a service technician performs any service procedure. Where applicable, steam and/or compressed air supplies should also be disconnected before service is performed. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232088 Operation This manual is designed as a guide to operating and programming the UW35 and UW60 rigid-mount washer-extractor equipped with the mechanical timer control. The manuals, installation instructions, and wiring diagrams which accompany the machine have been included with the machine at no charge. Additional copies are available at a nominal charge. NOTE: Read this manual thoroughly before attempting to operate the machine. NOTE: Do not use this manual in conjunction with earlier model UW machines. Do not use technical literature intended for earlier models when operating this machine. NOTE: All information, illustrations, and specifications contained in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. Customer Service If literature or replacement parts are required, contact the source from whom the machine was purchased or contact Alliance Laundry Systems LLC at (920) 748-3950 for the name and address of the nearest authorized parts distributor. For technical assistance, call (920) 748-3121 Ripon, Wisconsin. A record of each machine is on file with the manufacturer. Always provide the machine’s serial number and model number when ordering parts or when seeking technical assistance. F232088 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Machine Familiarization The machine familiarization guide in Figure 1 identifies major operational features of the UW washer-extractor. Door Handle Door Box Door Hinge Door Latch Extension Arm Door Latch Rub Rail FA001G Shell Front Control Module Supply Dispenser Door Latch Handle Side Panel Supply Valve Box Figure 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232088 Theory Of Operation The design of the machine emphasizes performance reliability and long service life. The cylinder, shell, and main body panels are fabricated of stainless steel. Electrical controls for the machine are housed in a separate enclosure located on the top of the machine. Removing the screws from the module cover, lifting the cover, and pulling to the rear provides access to the control module. This module contains the mechanical timer, contactors, water-level switch, and other control components. All models use one 2-speed motor to drive the cylinder via a V-belt drive in both speeds.The cylinder is supported via the shaft by two bearings. The UW35 uses two ball bearings held in place by a single cast- iron housing that is bolted to the A-frame. The UW60 uses two flange-mounted, spherical roller bearings bolted to the A-frame. The cylinder is constructed with lifters or ribs that lift the laundry from the bath solution when the cylinder rotates at slow speed and then allow the laundry to tumble back into the bath. This mechanical action accomplishes the washing function. The cylinder is perforated, allowing the water to drain from within during the wash and extract steps. On the UW60, a balance switch is installed between the faces of the A-frame to signal the controls to slow the machine when a severely out-of-balance load occurs during extract. Water enters the machine through electromechanical water valves controlled by the mechanical timer. The mechanical timer also controls the drain and door lock. In addition, the timer selects the water levels according to the selected cycle. A vacuum breaker is installed in the water-inlet plumbing to prevent backflow of water. Operation The standard production UW 2-speed model uses a single drain valve. (A dual drain is available as an option.) The drain valve is normally open, which means that it closes only when power is applied, thus allowing the machine to drain in the event of a power failure. A door-lock system prevents opening of the stainless steel door when a cycle is in progress. It also prevents operation of the machine when the door is open. The doorbox contains the door-lock microswitch, door- closed magnetic switch, and the door-unlock solenoid. The UW35 shaft seal assembly includes two lip seals integrated into the cast-iron bearing housing. Each seal has two lips which make contact with a polished stainless steel bushing mounted to the shaft. The UW60 shaft seal assembly includes a brass collar held in place on the cylinder shaft with set screws. The collar has a flange with a ceramic ring which makes contact with a spring-loaded phenolic face seal enclosed in a nylon housing mounted on the rear of the shell. The collar contains two internal O rings which maintain contact with the cylinder shaft. The polypropylene supply dispenser is mounted on the right side of the washer-extractor, ...


Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias