Log:
Assessments - 4, GPA: 3.8 ( )

Instruções de Operação GE Monogram, Modelo WHDSR417

Fabricante : GE Monogram
Arquivo Tamanho: 485.36 kb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Water leaks Fill hoses or drain hose is improperly connected • Make sure hose connections are tight at faucets and rubber washers are installed. Make sure end of drain hose is correctly inserted in and secured to drain facility. The drain hose should be inserted into the washer and the collar or clip should be screwed in. Remove any kinks from the drain hose. Make sure that the hose connection is not strained when the washer is pushed close to the wall. Household drain may be clogged • Check household plumbing. You may need to call a plumber. Constant water pressure to the fill • Tighten hoses at the faucets and turn the water off after hoses at the water source each use. • Check condition of the fill hoses; they should be replaced every 5 years. Using too much detergent in • Use less detergent. Use less soap if you have soft water, a washer smaller load or a lightly soiled load. Fill hoses, washers and screens • Check that the rubber washers and screens have been installed correctly. Fill hoses, washers and screens should be replaced every 5 years. Overloading the washer • Loosely load clothes no higher than the top row of holes in the washer basket. The level of the water should be just above the clothes. Water temperature Cooler water temperatures provide • New laundry detergents have been formulated to seems incorrect improved energy efficiency work with cooler water temperatures without affecting wash performance. Control is not set properly • Check water temperature control (on some models) or Cycle knob and adjust. Water supply is turned off • Turn both hot and cold faucets fully on and make sure or improperly connected hoses are connected to correct faucets. Water valve screens are • Turn off the water source and remove the water stopped up connection hoses from the upper back of the washer. Use a brush or toothpick to clean the screens in the machine. Reconnect the hoses and turn the water back on. House water heater is • Make sure house water heater is delivering water not set properly at 120°F–140°F (48°C–60°C). Water won’t drain Drain hose is kinked or • Straighten drain hose and make sure washer is not sitting improperly connected on it. • Top of drain outlet should be less than 8 ft. (2.5 m) above floor. 11 Consumer SupportTroubleshooting Instructions Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips Before you call for service… WATER Possible Causes What To Do Water fills and drains at the same time Siphoning • If your standpipe or drain for the washer is less than 3 feet off the floor, the water will drain from the tub while it is filling. Lifting the drain hose at least 3 feet off the floor will allow the water to remain in the tub until the pump drains it out. The anti-siphon clip will lift the drain hose high enough to do this. The anti-siphon clip is included with the installation parts package for your washer. • Another way siphoning can occur is if the standpipe is stuffed with rags or other items that prevent air from escaping with the water. Air flow is needed to break the suction. • Check to make sure only the straight part of the drain hose is inserted into the standpipe; no ribs of the drain hose should ...

Este manual também é adequado para os modelos :
Máquinas de lavar - WJRR4170 (485.36 kb)
Máquinas de lavar - WSERR417 (485.36 kb)
Máquinas de lavar - WLDSR416 (485.36 kb)
Máquinas de lavar - WJSR4160 (485.36 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias