|
Facilidade de uso
Important: before removing the lid check that the wash cycle has ended and unplug the washer-dryer from the mains. It is normal for a small quantity of water to spill out once the lid is removed. The panel positioned at the base of the machine will catch the water that spills out. Remember to shut the lid firmly when you replace it. GB 8 1 1 2 1 1 2 Fig. 1 Fig. 2 Trouble shooting If the machine does not seem to be working properly before calling the service engineer there are a number of things you can check. Perhaps you have forgotten to push in a button or you are not using the machine properly. Machine won't start Make sure: the appliance is plugged to the mains socket; you have electricity in your home, the door is firmly shut, the ON/OFF button D is on I, the programming cycle knob, in washer- dryers which have one, is on O, the programme is properly set and the mains water tap is open. Machine won't fill Make sure: the water tap is open and connected correctly to the hose; the water mains has not been cut off and that water pressure is sufficient; also check the hose for kinks. Water is pumping in and out all the time Make sure: there are no kinks in the drain pipe and that it is at least at a height of 60-100 cm; the pipe mouth is not below water level and that the wall drain has no air outlet. If the problems continue even after you have checked these points, shut the water tap and turn off your washer-dryer. Problems with pumping out water or spinning Make sure: the programme selected has a draining cycle; the non creasing "hydropstop" button, on washer-dryers which have one, has not been pressed accidentally; the drainage pump is not jammed; the drain pipe is bent; the drainage piping is plugged; any drainage pipe extensions are properly connected and do not prevent water flow. Removing limescale Water contains increasing amounts of limescale because of pollution. If you live in a hard water area in addition to using water-softener in each wash, it is a good idea to put the machine through a cycle without laundry or detergent, just using limescale remover. The washer-dryer is not drying Make sure: the plug is inserted properly into the socket; there is electricity in the house; the washer-dryer door is closed; the ON-OFF button D is on the I setting; the programming cycle knob, in washer-dryers which have one, is on the O setting; the program knob A is on the setting; the dryer knob B is on the O setting. Lots of vibration during the spin Make sure: the internal oscillating unit was released correctly at the time of installation (see installation instructions); the washer is levelled correctly or too tightly fitted between furniture units and the wall. Your washer is leaking. Make sure: the ring nut of the supply pipe is firmly tightened; the detergent dispenser is not plugged and the drainage pipe is firmly fixed. Excessive formation of suds. Make sure: the type of detergent you have used - is it suitable for an automati washer - have you used too much detergent? The washer-dryer is not drying efficiently. Make sure. the end of the drain hose is not immersed in water; the drain pump is not blocked (see "General maintenance"); the advice on maximum loads and drying times have been followed; the drying time selected is at least 20 minutes; the water tap is turned on. 9 GB If despite all this your washer-dryer is still not running properly, call your local Authorized Service Centre providing the following information: -fault -model code (Mod. ....) and serial number (S/N ....) shown on the data plate at the back of your washer. Never use the services of an unauthorised servicing technician and insist on the use of original spare parts. Installation Transit packing After removing the packing, check the appliance for damage. If you have any doubts do not use the washer and call a qualified technician. Keep the packaging components (plastic bags, polyester foam, nails etc.) out of the reach of children since they could be dangerous. The interior of the washer-dryer, has an oscillating unit which is fixed on the back by 3 screws during transport (figure 3). Before starting up the washer-dryer, release the unit, by unscrewing the 3 screws. Seal the screw holes with the plastic plugs supplied with the appliance. Fig. 3 Fig. 4 Levelling The washer-dryer must be perfectly levelled. To level the appliance, only the front feet need to be adjusted (see fig. 4); remember that the inclination of the working surface must not be more than 2 degrees. If the washer-dryer is installed on a carpeted floor, check that there is sufficient ventilation space between the floor and the bottom of the washer-dryer. Water supply Both hot and cold water supplies are preferable and they should be between 34.5kN/m.(5lb/in.) and 1034.2kN/m. (150lb/in.) pressure. The hose having the red end fitting should be encountered between the hot supply and the threaded connection adjacent to the letter H on the rear of the machine. The hose ...
Este manual também é adequado para os modelos :Máquinas de lavar - WDG 1095 WG (214.8 kb)
Máquinas de lavar - WDG 985 BG (214.8 kb)