Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
DO YOU NEED TO PRE-WASH? For heavily soiled laundry only! SAVE detergent, time, water and between 5 to 15% energy consumption by NOT selecting Prewash for slight to normally soiled laundry. IS A HOT WASH REQUIRED? Pretreat stains with stain remover or soak dried in stains in water before washing to reduce the necessity of a hot wash programme. SAVE up to 50% energy by using a 60°C wash programme. BEFORE USING A DRYING PROGRAMME ... SAVE energy and time by selecting the highest suitable spin speed to reduce the water content in laundry before using a drying programme. In compartment 1: Detergent for pre-washing (powder) In compartment 2: Detergent for washing (powder or liquid) In compartment 3: Additives (softeners, perfumes, etc.) In compartment 4: Bleach and delicate bleach. You cannot bleach with the “Silk” programme and with the “special programmes” (see page 4). Should you wish to bleach separately, pour the bleach into extra compartment 4, set the rinse programme for cotton fabrics or the light rinse for synthetics. The rinse level should be set to Medium or High (see page 3). When bleaching during a normal wash cycle, pour in the detergent and additives into the special compartments (see table on page 4), set the desired programme and select the stain erase option. Instructions for installation and us. Troubleshooting Before calling, read the following In most cases, when your washing machine fails to work, the problems arising can be easily solved without having to call for a technician. Before calling for assistance, always check these points. The washing machine fails to start. Is the plug correctly inserted into the socket? It could have been moved whilst cleaning. Is there electricity in the house? A circuit breaker may have switched off as a result of too many electrical appliances working at the same time. Or maybe due to a general failure in your entire area. Is the washing machine door closed properly? For safety reasons, the washing machine cannot work Turn off the water supply after use. This will eliminate the possibility ofleakage. Always leave theappliance door ajarto avoid bad odours. Clean the appliance’sexteriors gently. To clean the exteriors and the rubber parts of theappliance, alwaysuse a soft cloth dipped in warm and soapy water. RIGHT WRONG if the door is open or not shut properly. Is the On/Off button pressed? If it is, then a programmed start has been set. Has the Start/Reset button been pressed? If it is, then a programmed start has been set. Is the water supply turned on? For safety reasons, if the washing machine does not load water, it cannot start a wash cycle. Leave the washing machine plugged in while cleaning. Even during maintenance, the appliance should always be unplugged. Use solvents and aggressive abrasives. Never use solvents or abrasives to clean the external and rubber parts of the washing machine. Neglect the detergent dispenser. It is removable and can easily be cleaned by leaving it under running water. Go on holiday without thinking about her. Before leaving, always make sure that the washing machine is unplugged and that the water supply is turned off. Simple: with the new Indesit technology, you need less thanhalf of it, to get good results on twice as much! This is why you cannot see the water through the door: because there is little, very little of it, to respect theenvironment yet without renouncing maximum cleanliness. And, on top of that, you are also saving electricity. But where did all the water go? The washing machine fails to fill with water. Is the hose correctly connected to the tap? Is there a water shortage ? There could be work in progress in your building or street. Is there sufficient water pressure? The autoclave may be malfunctioning. Is the tap filter clean? If the water is very calcareous, or if work has recently been carried out on the water piping, the tap filter could be clogged with particles and debris. Is the rubber hose kinked? The tract of the rubber hose bringing water to washing machine must be as straight as possible. Make sure it is not squashed or kinked. The washing machine continuously fills and drains water. Is the drain hose positioned too low? It must be installed at a height ranging from 60 to 100 cm. Is the end of the hose immersed in water? Does the wall drainage system have a breather pipe? If the problem persists even after these checks, turn the water supply off the machine and call for assistance. If you live on an upper floor of your building, there may be a problem with your drain trap. To solve this problem, a special valve must be installed. Instructions for installation and us. Is there space between the The tract of the drain hose machine and adjacent must be as straight as units? If it is not a built-in possible. Make sure the drain model, the washing machine hose is not squashed or will oscillate a bit during the kinked. spin cycle. A few cm of space should therefore be left Is the drain hose kinked...