Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Clean the filter of the drain pump. Refer to 'Care and clean- ing'. The connection of the water drain hose is not correct. Make sure that the connection is correct. A washing programme without the drain phase is set. Set the drain programme. The function Rinse & Hold is on. Set the drain programme. The appliance door is open or not closed correct- ly. Close the door correctly. Problem Possible cause Possible solution The anti-flood de- vice is on. • Disconnect the appliance. • Close the water tap. • Contact the service centre. The spin phase The spin phase is off. Set the spin programme. does not operate. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and clean- ing'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The programme The mains plug is not Put in the mains plug. does not start. connected in the mains socket. You did not press button 4 . Press button 4 . The delay start is set. To start immediately the pro- gramme, cancel the delay start. The Child Lock function is activated. Deactivate the Child Lock func- tion. Blow out fuse in the Replace the fuse. household fuse box. There is water on Leakages from the cou-Make sure that the couplings are the floor. plings of the water ho-tight. ses. Leakages from the drain pump. Make sure that the drain pump filter is tight. The water drain hose is damaged. Make sure that the water inlet hose has no damages. You cannot open The washing programme Let the washing programme end. the appliance is in operation. door. There is water in the Set the drain or the spin pro- drum. gramme. The appliance Incorrect level of the ap-Adjust the level of the appliance. makes an unusual pliance. Refer to 'Installation'. noise. You did not remove the packaging and/or the transit bolts. Remove the packaging and/or the transit bolts. Refer to 'Instal- lation'. The load is very small. Add more laundry in the drum. ENGLISH 25 Problem Possible cause Possible solution The appliance fills with water and drain immediately. The end of the drain hose is too low. Make sure that the drain hose is in the correct position. The washing results are not satis- The detergent you used was not sufficient or cor- Increase the detergent quantity or use a different one. factory. rect. You did not remove the stubborn stains before Use special products to remove the stubborn stains. you wash the laundry. Incorrect temperature was set. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. After the check, activate the appliance. If the display shows other alarm codes, The programme continues from the contact the service centre. point of interruption. If the problem occurs again, contact the service centre. SERVICE • Refer to the information supplied with this appliance for guarantee condition and point of contact. The information to give to the service is on the rating plate. We recommend that you write the information here: Product number (PNC) .................. Model .................. Serial number .................. (MOD.) (S.N.) TECHNICAL DATA Dimensions Width / Height / Depth 605 / 850 / 605 mm Total depth 640 mm Electrical connection: Voltage Overall power Fuse Frequency 230 V 2200 W 10 A 50 Hz Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Water supply 1) Cold water Maximum load Cotton Spin speed Maximum 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 7 kg 1400 rpm (L 75478 FL) 1600 rpm (L 75678 FL) INSTALLATION UNPACKING 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polystyrene packaging materials. 4. Remove the internal film. ENGLISH 27 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 1 2 6. Put the front piece on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. 8. Pull up the appliance in vertical position. 9. Remove the power supply cable and the drain hose from the hose holders. 10 Remove the three bolts. Use the key . supplied with the appliance. 11 Pull out the plastic spacers. . 12 Replace the plastic spacers with the . plastic caps. You can find these caps in the user manual bag. WARNING! We recommend that you keep Remove all the packaging and the packaging and the transit the transit bolts before you in-bolts for when you move the ap stall the appliance. pliance. POSITIONING AND LEVELLING x4 • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in op...
Este manual também é adequado para os modelos :Máquinas de lavar - L 75675 FL (1.45 mb)