Assessments - 3, GPA: 3.7 ( )

Fabricante : Hotpoint Arquivo Tamanho: 1.2 mb Arquivo Nome : Língua de Ensino:

The following information is provided for your safety and should be read carefully. . This machine is designed for domestic use only. . Before using your machine make sure that the TWO transit bolts, TWO rubber grommets and TWO spacers have been removed (see page 5). . Any electrical work necessary to install this machine should be carried out by a qualified electrician. . Do not plug your machine into a socket when your hands are wet. . Do not try to modify this machine in any way. . Do not let children play with the machine or with its controls. . Do not lean on the door or use the door to lift or move the machine. . Do not wash garments that have previously been treated with solvents. . Do not connect the machine to a single outlet instantaneous water heater. . Do not connect the machine directly to a water- softening unit; use the recommended amount of detergent for the water hardness in your area. . Do not overload or underload the machine. In addition to reducing the quality of the wash, this may also damage your laundry and the machine. . Do not pull on the power supply cable to unplug the appliance from the electricity socket. Pull the plug out. . Do not touch the drain water as it could reach very high temperatures (over sink drainage). . Never force the machine door; this could damage the safety lock mechanism design to prevent any accidental opening. . In the event of a malfunction, do not under any circumstances touch internal parts in order to attempt repairs. . Should it have to be moved, proceed with the help of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy. . Before loading your laundry into the machine, make sure the drum is empty. . Be careful not to touch the drum at the top, as this area does get hot during drying. Technical Details Chart Models WD645, WD640, WD440, WD420 59.5cm wide Dimensions 85cm high 60cm deep Capacity From 1 to 6kg Wash From 1 to 5kg Dry Electric Voltage 220/240 50Hz connections Max absorbed power 1700W-2100W Water Maximum pressure 1 MPa (10 bar) connections Minimum pressure 0.05 MPa (0.5 bar) Drum capacity 54 litres Spin Speed up to 1400 rpm - WD645, WD640, WD440 up to 1200 rpm - WD420 Control 60.C cotton (programme D) programme with Wash Enhance according to -Wash run with a 6kg load IEC50229 -Dry run with 5kg and 1kg loads This appliance is compliant with the following European Community Directives: - 73/23/EEC & 93/68/EEC (Low Voltage) and subsequent amendments. - 89/336/EEC,92/31/EEC & 93/68/EEC (Electromagnetic Compatibility) and subsequent amendments. 20 Something Wrong? - Troubleshooting If your machine seems not to be working, GO through the following troubleshooting suggestions BEFORE you call your Service Centre (see Service). GB Section 1: All Aquarius Models - General Troubleshooting Problem: The machine won’t start: (Nothing lights up on the control panel). Lights illuminate on the control panel but the wash cycle will not start. The machine fails to fill with water. The machine does not drain or spin (during the first wash cycle, after installation). The machine does not drain or spin (although it has drained/spun during previous wash cycles). The programme takes a long time. Possible causes / Solution: . Check the appliance is fully plugged into the socket and switched on. . Is the socket ok? Try another appliance in the socket to check. . Is the fuse in the plug ok? If not, replace it, fuse must be 13 Amps (see Care and Maintenance). . There has been a power failure - Check another electrical device in your home to see if this is the case. . The ON/OFF button has not been pressed. . The Start/Cancel button has not been pressed, for at least 3 seconds - Press and hold the Start/Cancel button until the machine starts to operate. . The appliance door is not shut properly - Close the door firmly and try the machine again. . The Start/Cancel button has not been pressed, for at least 3 seconds - Press and hold the Start/Cancel button until the machine starts to operate. . The cold water supply tap is not turned on -Aquarius only: ‘Wash’ indicator light is flashing on the control panel. -Aquarius+ only: ‘H20’ is shown in the display. . Aquarius+ only: Have you selected Time Delay (see Programmes and Option Modifiers). . The Start/Cancel button has not been pressed, for at least 3 seconds - Press and hold the Start/Cancel button until the machine starts to operate. . The machine has failed to take in water (see Installation) -Is the ‘Wash’ indicator light flashing (Aquarius only)? -Is ‘H20’ shown in the display (Aquarius+ only)? Check that: -Both of the cold water inlet hoses are connected to the cold water supply tap, using the ‘Y’ piece connector. -The hoses are not kinked. -The cold water supply tap is turned on... Ensure that it is turned fully on. -The water pressure is sufficient (see Technical Details Chart). -The inlet filters are not blocked... Turn off the water, unscrew bot...

Baixe o seu

Para fazer o download, introduza 2 dígitos :